AS/NZS 4129:2020 Fittings for polyethylene (PE) pipes for pressure applications
- Abbreviation
- AS/NZS 4129:2020
- Valid from
- 21/02/2020
- Information provider
- Standards New Zealand,
- Author
- Standards New Zealand, Standards Australia
- Information type
- New Zealand Standard,
- Format
- PDF, HARD COPY,
Description
This Standard specifies requirements for fittings to be used with polyethylene pipe manufactured in accordance with AS/NZS 4130 or AS 2698.2 or POP 009.
Scope
This Standard is applicable to fittings manufactured for the conveyance of water, fuel gas, and other fluids including compressed air.
This resource is cited by:
AS/NZS 4129:2020 Fittings for polyethylene (PE) pipes for pressure applications
This document is CITED BY:
-
G12/AS1 (Amd 13) (Third Edition, Amendment 13)
AS/NZS 4129:2020 is cited by Acceptable Solution G12/AS1: Water Supplies from 2/11/2023
-
AS/NZS 2845.1:2022
AS/NZS 4129:2020 is cited by AS/NZS 2845.1:2022 Water supply - Backflow prevention devices - Part 1: Materials, design and performance requirements
-
AS/NZS 3500.3:2021
AS/NZS 4129:2020 is cited by AS/NZS 3500.3:2021 Plumbing and drainage, Part 3: Stormwater drainage
This resource cites:
AS/NZS 4129:2020 Fittings for polyethylene (PE) pipes for pressure applications
This document CITES:
AS/NZS 4129:2020 cites AS/NZS 2280:2014 Ductile iron pipes and fittings
AS/NZS 4129:2020 cites AS/NZS 3500.0:2003 Plumbing and drainage - Glossary of terms
AS/NZS 4129:2020 cites AS/NZS 4020:2018 Testing of products for use in contact with drinking water
AS/NZS 4129:2020 cites AS/NZS 4087:2011 Metallic flanges for waterworks purposes
AS/NZS 4129:2020 cites AS/NZS 4130:2018 Polyethylene (PE) pipes for pressure applications
AS/NZS 4129:2020 cites AS/NZS 4131:2010 Polyethylene (PE) compounds for pressure pipes and fittings
AS/NZS 4129:2020 cites AS/NZS 4158:2003 Thermal-bonded polymeric coatings on valves and fittings for water industry purposes
AS/NZS 4129:2020 cites AS/NZS 4331.1:1995 (R2016) Metallic flanges - Steel flanges
AS/NZS 4129:2020 cites AS/NZS 4331.2:1995 (R2016) Metallic flanges - Cast iron flanges
AS/NZS 4129:2020 cites AS/NZS 4331.3:1995 (R2016) Metallic flanges - Copper alloy and composite flanges
AS/NZS 4129:2020 cites AS 1049.1:2014 Telecommunication cables - Insulation sheath and jacket. Materials
AS/NZS 4129:2020 cites AS 1049.2-2008 Telecommunication cables - Insulation sheath and jacket. Test methods.
AS/NZS 4129:2020 cites AS 1145.2-2001 Determination of tensile properties of plastics materials - Part 2: Test conditions for moulding and extrusion plastics
AS/NZS 4129:2020 cites AS 1199.1-2003 (R2016) Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
AS/NZS 4129:2020 cites AS 1722.2-1992 (R2017) Pipe threads of Whitworth form - Part 2: Fastening pipe threads
AS/NZS 4129:2020 cites AS 2129-2000 (R2016) Flanges for pipes valves and fittings
AS/NZS 4129:2020 cites AS 2193-2005 (R2017) Calibration and classification of force-measuring systems
AS/NZS 4129:2020 cites AS 2345-2006 (R2016) Dezincification resistance of copper alloys
AS/NZS 4129:2020 cites AS 2698.2-2000 (R2017) Plastics pipes and fittings for irrigation and rural applications - Polyethylene rural pipe
AS/NZS 4129:2020 cites AS 3688:2016 Water supply and gas systems - Metallic fittings and end connectors
AS/NZS 4129:2020 cites AS ISO 7.1-2008 (R2017) Pipe threads where pressure-tight joints are made on the threads - Dimensions, tolerances and designation
AS/NZS 4129:2020 cites AS ISO 9624-2008 Polyethylene (PE) pipes for fluids under pressure - Mating dimensions of flange adaptors and loose backing flang
AS/NZS 4129:2020 cites AS ISO/IEC 17025:2018 General requirements for the competence of testing and calibration laboratories
AS/NZS 4129:2020 cites ASME B16.47:2017 Large Diameter Steel Flanges: NPS 26 through NPS 60 Metric/Inch Standard
AS/NZS 4129:2020 cites ASME B16.5:2017 Pipe Flanges And Flanged Fittings: Nps 1/2 Through Nps 24 Metric/inch Standard
AS/NZS 4129:2020 cites ASTM A276/A276M-17 Standard Specification for Stainless Steel Bars and Shapes
AS/NZS 4129:2020 cites ASTM D1600 - 18 Standard Terminology for Abbreviated Terms Relating to Plastics
AS/NZS 4129:2020 cites BS EN 12201-3:2011+A1:2012 Plastics piping systems for water supply, and for drainage and sewerage under pressure. Polyethylene (PE) - Fittings
AS/NZS 4129:2020 cites BS EN 12814-3:2014 Testing of welded joints in thermoplastics semi-finished products - Part 3: Tensile creep test
AS/NZS 4129:2020 cites BS EN 12842:2012 Ductile iron fittings for PVC-U or PE piping systems. Requirements and test methods
AS/NZS 4129:2020 cites BS EN 14525:2004 Ductile iron wide tolerance couplings and flange adaptors for use with pipes of different materials: ductile iron, grey iron, steel, PVC-U, PE, fibre-cement
AS/NZS 4129:2020 cites BS EN 1555-3:2010+A1:2012 Plastics piping systems for the supply of gaseous fuels. Polyethylene (PE) - Part 3: Fittings
AS/NZS 4129:2020 cites BS EN ISO 1167-1:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method
AS/NZS 4129:2020 cites BS EN ISO 1167-2:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 2: Preparation of pipe test pieces
AS/NZS 4129:2020 cites BS EN ISO 1167-4:2007 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 4: Preparation of assemblies.
AS/NZS 4129:2020 cites IEC 60529:1989 Degrees of protection provided by enclosures (IP Code)
AS/NZS 4129:2020 cites ISO 1043-1:2011 Plastics - Symbols and abbreviated terms - Part 1: Basic polymers and their special characteristics
AS/NZS 4129:2020 cites ISO 1133-1:2011 Plastics — Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics — Part 1: Standard method.
AS/NZS 4129:2020 cites ISO 11357-6:2018 Plastics - Differential scanning calorimetry (DSC). Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT)
AS/NZS 4129:2020 cites ISO 11413:2019 Plastics pipes and fittings - Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting
AS/NZS 4129:2020 cites ISO 12176-2:2008 Preview Plastics pipes and fittings -- Equipment for fusion jointing polyethylene systems -- Part 2: Electrofusion
AS/NZS 4129:2020 cites ISO 12176-4:2003 Plastics pipes and fittings - Equipment for fusion jointing polyethylene systems - Part 4: Traceablity coding
AS/NZS 4129:2020 cites ISO 13460-1:2015 Agricultural irrigation equipment — Plastics saddles — Part 1: Polyethylene pressure pipes
AS/NZS 4129:2020 cites ISO 13950:2007 Plastics pipes and fittings — Automatic recognition systems for electrofusion joints
AS/NZS 4129:2020 cites ISO 13951:2015 Plastics piping systems - Test method for the resistance of plastic pipe/pipe or pipe/fitting assemblies to tensile loading
AS/NZS 4129:2020 cites ISO 13953:2001 Polyethylene (PE) pipes and fittings - Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
AS/NZS 4129:2020 cites ISO 13954:1997 Plastics pipes and fittings - Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
AS/NZS 4129:2020 cites ISO 13955:1997 Plastics pipes and fittings - Crushing decohesion test for polyethylene (PE) electrofusion assemblies
AS/NZS 4129:2020 cites ISO 13956:2010 Plastics pipes and fittings — Decohesion test of polyethylene (PE) saddle fusion joints — Evaluation of ductility of fusion joint interface by tear test
AS/NZS 4129:2020 cites ISO 13957:1997 Plastics pipes and fittings - Polyethylene tapping tees - Test methods for impact resistance
AS/NZS 4129:2020 cites ISO 15494:2015 Plastics piping systems for industrial applications — Polybutene (PB), polyethylene (PE), polyethylene of raised temperature resistance (PE-RT), crosslinked polyethylene (PE-X), polypropylene (PP) — Metric series for specifications for comp
AS/NZS 4129:2020 cites ISO 17885:2015 Plastics piping systems — Mechanical fittings for pressure piping systems — Specifications
AS/NZS 4129:2020 cites ISO 21751:2011 Plastics pipes and fittings — Decohesion test of electrofusion assemblies — Strip-bend test
AS/NZS 4129:2020 cites ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation
AS/NZS 4129:2020 cites ISO 3126:2005 Plastics piping systems - Plastics components - Determination of dimensions
AS/NZS 4129:2020 cites ISO 3459:2015 Plastic piping systems — Mechanical joints between fittings and pressure pipes — Test method for leaktightness under negative pressure.
AS/NZS 4129:2020 cites ISO 3501:2015 Plastics piping systems — Mechanical joints between fittings and pressure pipes — Test method for resistance to pull-out under constant longitudinal force
AS/NZS 4129:2020 cites ISO 3503:2015 Plastics piping systems — Mechanical joints between fittings and pressure pipes — Test method for leaktightness under internal pressure of assemblies subjected to bending
AS/NZS 4129:2020 cites ISO 4427-3:2019 Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 3: Fittings
AS/NZS 4129:2020 cites ISO 6957:1988 Copper alloys - Ammonia test for stress corrosion resistance
AS/NZS 4129:2020 cites ISO 7686:2005 Plastics pipes and fittings - Determination of opacity
AS/NZS 4129:2020 cites ISO 9080:2012 Plastics piping and ducting systems - Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation
AS/NZS 4129:2020 cites PIPA POP009 - Polyethylene Rural And Flood Pipe