Skip to main content Skip to primary navigation
Resource detail
Citations

AS 1199.1-2003 (R2016) Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection

View on Information Provider website
Abbreviation
AS 1199.1-2003 (R2016)
Valid from
28/07/2003
Information provider
Intertek Inform,
Author
Standards Australia
Information type
Australian Standard,
Format
PDF, HARD COPY,
Cited By
This resource is cited by 18 documents (show Citations)
Description

This Standard specifies an acceptance sampling system for inspection by attributes. It is indexed in terms of the acceptance quality limit (AQL). Its purpose is to induce a supplier through the economic and psychological pressure of lot non-acceptance to maintain a process average at least as good as the specified acceptance quality limit, while at the same time providing an upper limit for the risk to the consumer of accepting the occasional poor lot.

Sampling schemes designated in this part of ISO 2859 are applicable, but not limited, to inspection of

  • end items,
  • components and raw materials,
  • operations,
  • materials in process,
  • supplies in storage,
  • maintenance operations,
  • data or records, and
  • administrative procedures.

These schemes are intended primarily to be used for a continuing series of lots, that is, a series long enough to allow the switching rules (9.3) to be applied.

These rules provide:

  • a) a protection to the consumer (by means of a switch to tightened inspection or discontinuation of sampling inspection) should a deterioration in quality be detected;
  • b) an incentive (at the discretion of the responsible authority) to reduce inspection costs (by means of a switch to reduced inspection) should consistently good quality be achieved.

Sampling plans in this Standard may also be used for the inspection of lots in isolation but, in this case the user is strongly advised to consult the operating characteristic curves to find a plan that will yield the desired protection (see 12.6). In that case, the user is also referred to the sampling plans indexed by limiting quality (LQ) given in AS 1199.2-2003 (R2016).

For assistance with locating previous versions, please contact the information provider.
Notes/comments

This Standard was reconfirmed 22 July 2016

View on Information Provider website
For assistance with locating previous versions, please contact the information provider.

This Standard was reconfirmed 22 July 2016

This resource is cited by:

AS 1199.1-2003 (R2016) Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection

This document is CITED BY:

AS 1199.1-2003 (R2016) Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection

Description

This Standard specifies an acceptance sampling system for inspection by attributes. It is indexed in terms of the acceptance quality limit (AQL). Its purpose is to induce a supplier through the economic and psychological pressure of lot non-acceptance to maintain a process average at least as good as the specified acceptance quality limit, while at the same time providing an upper limit for the risk to the consumer of accepting the occasional poor lot.

Sampling schemes designated in this part of ISO 2859 are applicable, but not limited, to inspection of

  • end items,
  • components and raw materials,
  • operations,
  • materials in process,
  • supplies in storage,
  • maintenance operations,
  • data or records, and
  • administrative procedures.

These schemes are intended primarily to be used for a continuing series of lots, that is, a series long enough to allow the switching rules (9.3) to be applied.

These rules provide:

  • a) a protection to the consumer (by means of a switch to tightened inspection or discontinuation of sampling inspection) should a deterioration in quality be detected;
  • b) an incentive (at the discretion of the responsible authority) to reduce inspection costs (by means of a switch to reduced inspection) should consistently good quality be achieved.

Sampling plans in this Standard may also be used for the inspection of lots in isolation but, in this case the user is strongly advised to consult the operating characteristic curves to find a plan that will yield the desired protection (see 12.6). In that case, the user is also referred to the sampling plans indexed by limiting quality (LQ) given in AS 1199.2-2003 (R2016).

View on Information Provider website
AS 1199.1-2003 (R2016) Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
Description

This Standard specifies an acceptance sampling system for inspection by attributes. It is indexed in terms of the acceptance quality limit (AQL). Its purpose is to induce a supplier through the economic and psychological pressure of lot non-acceptance to maintain a process average at least as good as the specified acceptance quality limit, while at the same time providing an upper limit for the risk to the consumer of accepting the occasional poor lot.

Sampling schemes designated in this part of ISO 2859 are applicable, but not limited, to inspection of

  • end items,
  • components and raw materials,
  • operations,
  • materials in process,
  • supplies in storage,
  • maintenance operations,
  • data or records, and
  • administrative procedures.

These schemes are intended primarily to be used for a continuing series of lots, that is, a series long enough to allow the switching rules (9.3) to be applied.

These rules provide:

  • a) a protection to the consumer (by means of a switch to tightened inspection or discontinuation of sampling inspection) should a deterioration in quality be detected;
  • b) an incentive (at the discretion of the responsible authority) to reduce inspection costs (by means of a switch to reduced inspection) should consistently good quality be achieved.

Sampling plans in this Standard may also be used for the inspection of lots in isolation but, in this case the user is strongly advised to consult the operating characteristic curves to find a plan that will yield the desired protection (see 12.6). In that case, the user is also referred to the sampling plans indexed by limiting quality (LQ) given in AS 1199.2-2003 (R2016).

View on Information Provider website
This resource does not cite any other resources.

AS 1199.1-2003 (R2016) Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection

This resource does not CITE any other resources.
Feedback