AS 4032.1-2005 Water supply - Valves for the control of heated water supply temperatures - Part 1: Thermostatic mixing valves - Materials design and performance requirements
- Abbreviation
- AS 4032.1-2005
- Valid from
- 28/01/2005
- Information provider
- Intertek Inform,
- Author
- Standards Australia
- Information type
- Australian Standard,
- Format
- PDF, HARD COPY,
Description
This Standard specifies requirements for the design, construction, testing performance and means of compliance for metallic-bodied thermostatic mixing valves.
Scope
This Standard specifies requirements for the design, construction, testing performance and means of compliance for metallic-bodied thermostatic mixing valves -
- (a) of nominal sizes not larger than DN50;
- (b) for use with hot water at a supply temperature not exceeding 90C; and
- (c) for use with hot and cold water with working pressures not exceeding 1400kPa.
When used for ablutionary purposes, thermostatic mixing valves complying with this Standard provide the user with reasonable protection against scalding or excessive temperature fluctuations due to variations of pressures and temperatures of the hot and cold water supplies, including shut-off of either the cold or hot water supply.
Notes:
- 1) Diagrams in this Standard are typical and chosen without prejudice.
- 2) Thermostatic mixing valves require routine maintenance and performance testing in accordance with AS4032.3.
This resource is cited by:
AS 4032.1-2005 Water supply - Valves for the control of heated water supply temperatures - Part 1: Thermostatic mixing valves - Materials design and performance requirements
This document is CITED BY:
-
G12/AS1 (Amd 13) (Third Edition, Amendment 13)
AS 4032.1-2005 is cited by Acceptable Solution G12/AS1: Water Supplies from 2/11/2023
-
AS 4032.2-2005 (R2015)
AS 4032.1-2005 is cited by AS 4032.2-2005 (R2015) Water supply - Valves for the control of hot water supply temperatures. Part 2: Tempering valves and end-of-line temperature-actuated devices
-
AS 4032.4:2014
AS 4032.1-2005 is cited by AS 4032.4:2014 Water supply - Valves for the control of heated water supply temperatures. Part 4: Thermostatically controlled taps for the control of heated water supply temperatures
-
AS/NZS 3500.4:2015
AS 4032.1-2005 is cited by AS/NZS 3500.4:2015 Plumbing and drainage - Heated water services
-
AS/NZS 3500.4:2018
AS 4032.1-2005 is cited by AS/NZS 3500.4:2018 Plumbing and drainage Part 4: Heated water services
This resource cites:
AS 4032.1-2005 Water supply - Valves for the control of heated water supply temperatures - Part 1: Thermostatic mixing valves - Materials design and performance requirements
This document CITES:
AS 4032.1-2005 cites AS/NZS 1167.1:2005 Welding and brazing - Filler metals - Filler metal for brazing and braze welding
AS 4032.1-2005 cites AS/NZS 1567:1997 Copper and copper alloys - Wrought rods, bars and sections
AS 4032.1-2005 cites AS/NZS 3000:2000 Electrical installations (known as the Australian/New Zealand Wiring Rules)
AS 4032.1-2005 cites AS/NZS 3499:1997 Flexible tube connectors for water supply
AS 4032.1-2005 cites AS/NZS 3500.0:2003 Plumbing and drainage - Glossary of terms
AS 4032.1-2005 cites AS/NZS 4020:2005 Testing of products for use in contact with drinking water
AS 4032.1-2005 cites NZS 3501:1976 Specification for copper tubes for water, gas, and sanitation - SPONSORED
AS 4032.1-2005 cites AS 1199.0-2003 (2016) Sampling procedures for inspection by attributes - Part 0: Introduction to the ISO 2859 attribute sampling system
AS 4032.1-2005 cites AS 1199.1-2003 (R2016) Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
AS 4032.1-2005 cites AS 1199.2-2003 (R2016) Sampling procedures for inspection by attributes - Part 2: Sampling plans indexed by limiting quality (LQ) for isolated lot inspection
AS 4032.1-2005 cites AS 1199.3-2003 (R2016) Sampling procedures for inspection by attributes - Part 3: Skip-lot sampling procedures
AS 4032.1-2005 cites AS 1199.4-2003 (R2016) Sampling procedures for inspection by attributes - Part 4: Procedures for assessment of declared quality levels
AS 4032.1-2005 cites AS 1432-2004 (R2016) Copper tubes for plumbing, gasfitting and drainage applications
AS 4032.1-2005 cites AS 1449-1994 Wrought alloy steels - Stainless and heat-resisting steel plate, sheet and strip
AS 4032.1-2005 cites AS 1565-1996 Copper and copper alloys - Ingots and castings
AS 4032.1-2005 cites AS 1568-1985 Copper and copper alloys - Forging stock and forgings
AS 4032.1-2005 cites AS 1572-1998 (R2018) Copper and copper alloys - Seamless tubes for engineering purposes
AS 4032.1-2005 cites AS 1769-1975 (R2018) Welded stainless steel tubes for plumbing applications
AS 4032.1-2005 cites AS 1834.1-1991 (R2018) Material for soldering - Part 1: Solder alloys
AS 4032.1-2005 cites AS 1881-1986 (R2018) Zinc alloys - Casting Ingots and casting - Quality - requirements
AS 4032.1-2005 cites AS 2345-2006 (R2016) Dezincification resistance of copper alloys
AS 4032.1-2005 cites AS 2738-2000 (R2018) Copper and copper alloys - Compositions and designations of refinery products, wrought products, ingots and castings
AS 4032.1-2005 cites AS 2831-1985 Thermometers - Solid stem - Long and short - For precision use
AS 4032.1-2005 cites AS 2837-1986 Wrought alloy steels - Stainless steel bars and semi-finished products
AS 4032.1-2005 cites AS 3558.5-1999 (R2016) Methods of testing plastics and composite materials sanitary plumbing fixtures - Method 5: Determination of degradation by ultraviolet light
AS 4032.1-2005 cites AS 3688-2005 Water supply - Metallic fittings and end connectors
AS 4032.1-2005 cites AS 4032.3-2004 Water supply - Valves for the control of heated water supply temperatures. Part 3: Requirements for field-testing, maintenance or replacement of thermostatic mixing valves, tempering valves and end-of-line temperature control devices
AS 4032.1-2005 cites ASTM A269-04 Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General Service
AS 4032.1-2005 cites ASTM A276 - 05a Standard Specification for Stainless Steel Bars and Shapes
AS 4032.1-2005 cites ASTM A313 / A313M - 03 Standard Specification for Stainless Steel Spring Wire
AS 4032.1-2005 cites ASTM B127-05 Standard Specification for Nickel-Copper Alloy (UNS N04400) Plate, Sheet, and Strip
AS 4032.1-2005 cites ASTM B163-04 Standard Specification for Seamless Nickel and Nickel Alloy Condenser and Heat-Exchanger Tubes
AS 4032.1-2005 cites ASTM B164-03 Standard Specification for Nickel-Copper Alloy Rod, Bar, and Wire
AS 4032.1-2005 cites ASTM B165-05 Standard specification for nickel-copper alloy (UNS N04400) seamless pipe and tube
AS 4032.1-2005 cites HB 18.28-2005 Conformity assessment - Guidance on a third-party certification system for products