AS/NZS 5601.1:2010 Gas installations - Part 1: General installations
- Abbreviation
- AS/NZS 5601.1:2010
- Amendment
- A1 - incorporated. Published 18/08/2011.
- Valid from
- 22/12/2010
- Replaces
- NZS 5261:2003, , , ,
- Information provider
- Standards New Zealand,
- Author
- Standards New Zealand, Standards Australia
- Information type
- New Zealand Standard,
- Format
- PDF, HARD COPY,
Description
This Standard contains the mandatory requirements and means of compliance for the design, installation and commissioning of gas installations that are associated with the use or intended use of fuel gases such as natural gas, LP Gas, biogas or manufactured gas.
Scope
The user is expected to be familiar with the properties and characteristics of those fuel gases and the principles of combustion, ventilation and flueing applicable to the safe installation and operation of gas appliances. For New Zealand, these requirements cover gas installations downstream of the point of supply (as defined in the Gas (Safety and Measurement) Regulations 2010.
Where the term installation is used it is deemed to include the pipework, appliances, flues, air ducts, ventilation and other ancillary items. Section 2 of this Standard contains the performance requirements for the design, installation, and commissioning of gas installations, including those operating at pressures exceeding 200 kPa. It includes, in Clause 2.6.4, some specific limitations as the performance requirements cannot be reliably met if those prohibitions are breeched. Sections 3 to 6 of this Standard contain a means of compliance for installations designed to operate with a gas supply pressure not exceeding 200 kPa.
In New Zealand, the Technical Regulator does not provide approvals for variations to the means of compliance in Sections 3 to 6. References to approval by the Technical Regulator are not applicable to New Zealand. The installation certifier is responsible for ensuring that the installation, including any variations, meets the requirements in Section 2. Where a Standard is cited as part of a means of compliance or in an Appendix, any Standard with equivalent performance requirements may be used as an alternative means of compliance in New Zealand.
This resource is cited by:
AS/NZS 5601.1:2010 Gas installations - Part 1: General installations
This document is CITED BY:
-
C/AS1 (Amd 3) (Amendment 3)
AS/NZS 5601.1:2010 is cited by Acceptable Solution C/AS1: Buildings with Sleeping (residential) and Outbuildings (Risk Group SH) from 19/12/2003
-
C/AS1 (Amd 5) (First Edition, Amendment 5)
AS/NZS 5601.1:2010 is cited by Acceptable Solution C/AS1: Buildings with Sleeping (residential) and Outbuildings (Risk Group SH) from 19/12/2003
-
C/AS1 (Amd 4) (First edition, amendment 4)
AS/NZS 5601.1:2010 is cited by Acceptable Solution C/AS1: Buildings with Sleeping (residential) and Outbuildings (Risk Group SH) from 19/12/2003
-
C/AS1 (Amd 2) (Amendment 2)
AS/NZS 5601.1:2010 is cited by Acceptable Solution C/AS1: Buildings with Sleeping (residential) and Outbuildings (Risk Group SH) from 19/12/2003
-
C/AS2 (First Edition, Amd 1 (Errata 1) (First Edition, Amendment 1 (Errata1 - 22/10/2019))
AS/NZS 5601.1:2010 is cited by Acceptable Solution C/AS2: Buildings other than Risk Group SH from 27/06/2019 until 3/11/2021
-
C/AS2 (First edition, amendment 4)
AS/NZS 5601.1:2010 is cited by Acceptable Solution C/AS2: Buildings with Sleeping (non institutional) (Risk Group SM) from 19/12/2013
-
C/AS2 (Amendment 2)
AS/NZS 5601.1:2010 is cited by Acceptable Solution C/AS2: Buildings with Sleeping (non institutional) (Risk Group SM) from 19/12/2013
-
C/AS2 (Amendment 3)
AS/NZS 5601.1:2010 is cited by Acceptable Solution C/AS2: Buildings with Sleeping (non institutional) (Risk Group SM) from 19/12/2013
-
C/AS3 (First edition, amendment 4)
AS/NZS 5601.1:2010 is cited by Acceptable Solution C/AS3: Buildings Where Care or Detention is Provided (Risk Group SI) from 19/12/2013
-
C/AS3 (Amendment 2)
AS/NZS 5601.1:2010 is cited by Acceptable Solution C/AS3: Buildings Where Care or Detention is Provided (Risk Group SI) from 19/12/2013
-
C/AS3 (Amendment 3)
AS/NZS 5601.1:2010 is cited by Acceptable Solution C/AS3: Buildings Where Care or Detention is Provided (Risk Group SI) from 19/12/2013
-
C/AS4 (Amendment 3)
AS/NZS 5601.1:2010 is cited by Acceptable Solution C/AS4: Buildings with Public Access and Educational Facilities (Risk Group CA) from 19/12/2013
-
C/AS4 (Amendment 2)
AS/NZS 5601.1:2010 is cited by Acceptable Solution C/AS4: Buildings with Public Access and Educational Facilities (Risk Group CA) from 19/12/2013
-
C/AS4 (First edition, amendment 4)
AS/NZS 5601.1:2010 is cited by Acceptable Solution C/AS4: Buildings with Public Access and Educational Facilities (Risk Group CA) from 19/12/2013
-
C/AS5 (First edition, amendment 4)
AS/NZS 5601.1:2010 is cited by Acceptable Solution C/AS5: Buildings used for Business, Commercial and Low Level Storage (Risk Group WB) from 19/12/2013
-
C/AS5 (Amendment 3)
AS/NZS 5601.1:2010 is cited by Acceptable Solution C/AS5: Buildings used for Business, Commercial and Low Level Storage (Risk Group WB) from 19/12/2013
-
C/AS5 (Amendment 2)
AS/NZS 5601.1:2010 is cited by Acceptable Solution C/AS5: Buildings used for Business, Commercial and Low Level Storage (Risk Group WB) from 19/12/2013
-
C/AS6 (Amendment 3.)
AS/NZS 5601.1:2010 is cited by Acceptable Solution C/AS6: Buildings used for High Level Storage and Other High Risk Purposes (Risk Group WS) from 19/12/2013
-
C/AS6 (Amendment 2)
AS/NZS 5601.1:2010 is cited by Acceptable Solution C/AS6: Buildings used for High Level Storage and Other High Risk Purposes (Risk Group WS) from 19/12/2013
-
C/AS6 (First edition, amendment 4)
AS/NZS 5601.1:2010 is cited by Acceptable Solution C/AS6: Buildings used for High Level Storage and Other High Risk Purposes (Risk Group WS) from 19/12/2013
-
G10/AS1 (First Edition, Amendment 7)
AS/NZS 5601.1:2010 is cited by Acceptable Solution G10/AS1: Piped Services from 23/06/2007
-
G11/AS1 (Amd 5) (First Edition, Amendment 5)
AS/NZS 5601.1:2010 is cited by Acceptable Solution G11/AS1: Gas as an Energy Source from 30/09/2010
-
G4/AS1 (Third Edition, Amendment 3)
AS/NZS 5601.1:2010 is cited by Acceptable Solution G4/AS1: Ventilation from 10/10/2011
-
G10/VM1 (First Edition, Amendment 7)
AS/NZS 5601.1:2010 is cited by Verification Method G10/VM1: Piped Services from 23/06/2007
-
AS/NZS 3000:2007
AS/NZS 5601.1:2010 is cited by AS/NZS 3000:2007 Electrical installations (known as the Australian/New Zealand Wiring Rules)
-
NZS 4246:2016
AS/NZS 5601.1:2010 is cited by NZS 4246:2016 Energy efficiency - Installing bulk thermal insulation in residential buildings - SPONSORED
This resource cites:
AS/NZS 5601.1:2010 Gas installations - Part 1: General installations
This document CITES:
AS/NZS 5601.1:2010 cites AS/NZS 1167.1:2005 Welding and brazing - Filler metals - Filler metal for brazing and braze welding
AS/NZS 5601.1:2010 cites AS/NZS 1260:2009 PVC-U Pipes and fittings for drain, waste and vent applications
AS/NZS 5601.1:2010 cites AS/NZS 1477:2006 PVC pipes and fittings for pressure applications
AS/NZS 5601.1:2010 cites AS/NZS 1518:2002 (R2016) External extruded high-density-polyethylene coating system for pipes
AS/NZS 5601.1:2010 cites AS/NZS 1530.3:1999 (R2016) Methods for fire tests on building materials, components and structures - Simultaneous determination of ignitability, flame propagation, heat release and smoke release
AS/NZS 5601.1:2010 cites AS/NZS 1734:1997 Aluminium and aluminium alloys - Flat sheet, coiled sheet and plate
AS/NZS 5601.1:2010 cites AS/NZS 1869:1996 Hose and hose assemblies for liquefied petroleum gases (LP Gas), natural gas and town gas
AS/NZS 5601.1:2010 cites AS/NZS 2648.1:1995 Underground marking tape - Non-detectable tape
AS/NZS 5601.1:2010 cites AS/NZS 2918:2001 Domestic solid fuel burning appliances - Installation
AS/NZS 5601.1:2010 cites AS/NZS 4129:2008 Fittings for polyethylene (PE) pipes for pressure applications
AS/NZS 5601.1:2010 cites AS/NZS 4130:2009 Polyethylene (PE) pipes for pressure applications
AS/NZS 5601.1:2010 cites AS/NZS 4645.3:2008 Gas distribution networks - Part 3: Plastics pipe systems
AS/NZS 5601.1:2010 cites AS/NZS 60079.10.1:2009 Explosive atmospheres - Part 10.1: Classification of areas - Explosive gas atmospheres
AS/NZS 5601.1:2010 cites NZS 4219:2009 Seismic performance of engineering systems in buildings - SPONSORED
AS/NZS 5601.1:2010 cites NZS/AS 1530.1:1994 (R2016) Methods for fire tests on building materials, components and structures - Part 1: Combustibility test for materials
AS/NZS 5601.1:2010 cites AS 1074-1989 (R2018) Steel tubes and tubulars for ordinary service
AS/NZS 5601.1:2010 cites AS 1210-2010 (R2021) Pressure vessels
AS/NZS 5601.1:2010 cites AS 1345-1995 (R2018) Identification of the contents of pipes, conduits and ducts
AS/NZS 5601.1:2010 cites AS 1357.1-2009 Valves primarily for use in heated water systems - Part 1: Protection valves
AS/NZS 5601.1:2010 cites AS 1397-2001 Steel sheet and strip - Hot-dipped zinc-coated or aluminium/zinc-coated
AS/NZS 5601.1:2010 cites AS 1432-2004 (R2016) Copper tubes for plumbing, gasfitting and drainage applications
AS/NZS 5601.1:2010 cites AS 1572-1998 (R2018) Copper and copper alloys - Seamless tubes for engineering purposes
AS/NZS 5601.1:2010 cites AS 2129-2000 (R2016) Flanges for pipes valves and fittings
AS/NZS 5601.1:2010 cites AS 2700-1996 Colour Standards for general purposes
AS/NZS 5601.1:2010 cites AS 2738-2000 (R2018) Copper and copper alloys - Compositions and designations of refinery products, wrought products, ingots and castings
AS/NZS 5601.1:2010 cites AS 2944.1-2007 Plastics pipes and fittings for gas reticulation - Part 1: Polyamide pipes
AS/NZS 5601.1:2010 cites AS 2944.2-2007 Plastics pipes and fittings for gas reticulation - Part 2: Polyamide fittings
AS/NZS 5601.1:2010 cites AS 3673-1989 Malleable cast iron threaded pipe fittings
AS/NZS 5601.1:2010 cites AS 3688-2005 Water supply - Metallic fittings and end connectors
AS/NZS 5601.1:2010 cites AS 3814-2009 Industrial and commercial gas-fired appliances
AS/NZS 5601.1:2010 cites AS 4041-2006 (R2016) Pressure piping
AS/NZS 5601.1:2010 cites AS 4176-1994 Polyethylene/aluminium and cross-linked polyethylene/aluminium macro-composite pipe systems for pressure applications
AS/NZS 5601.1:2010 cites AS 4553-2008 Gas space heating appliances
AS/NZS 5601.1:2010 cites AS 4566-2005 (R2017) Flue cowls - Gas appliances
AS/NZS 5601.1:2010 cites AS 4567-2005 (R2017) Twin wall metal flues - Gas appliances
AS/NZS 5601.1:2010 cites AS 4617-2004 Manual shut off gas valves
AS/NZS 5601.1:2010 cites AS 4623-2008 (R2016) Jointing compounds and materials for use in gas pipe joints
AS/NZS 5601.1:2010 cites AS 4627-2005 Quick-connect devices for gas
AS/NZS 5601.1:2010 cites AS 4629-2005 (R2018) Automatic shut off valves and vent valves
AS/NZS 5601.1:2010 cites AS 4631-2005 Limited flexibility connectors for gas
AS/NZS 5601.1:2010 cites AS D26-1972 (R2018) Tube fittings with dryseal American standard taper pipe and unified threads for automotive and industrial use
AS/NZS 5601.1:2010 cites AS ISO 6993.1-2007 (R2017) Buried, high-impact poly(vinyl chloride) (PVC-HI) piping systems for the supply of gaseous fuels - Part 1: Pipes for a maximum operating pressure of 1 bar (100 kPa) (ISO 6993-1:2006, MOD)
AS/NZS 5601.1:2010 cites AS ISO 6993.3-2007 (R2017) Buried, high-impact poly(vinyl chloride) (PVC-HI) piping systems for the supply of gaseous fuels - Part 3: Fittings and saddles for a maximum operating pressure of 1 bar (100 kPa)
AS/NZS 5601.1:2010 cites AS ISO 7.1-2008 (R2017) Pipe threads where pressure-tight joints are made on the threads - Dimensions, tolerances and designation
AS/NZS 5601.1:2010 cites Hazardous Substances (Dangerous Goods and Scheduled Toxic Substances) Transfer Notice 2004
AS/NZS 5601.1:2010 cites ANSI/ASME B1.20.1:1983 (R2006) Pipe threads general purpose (Inch)
AS/NZS 5601.1:2010 cites API SPEC 5L-2007 Specification for Line Pipe
AS/NZS 5601.1:2010 cites ASME B16.11-2009 Forged Fittings, Socket-welding And Threaded
AS/NZS 5601.1:2010 cites ASME B16.5:2009 Pipe Flanges And Flanged Fittings: Nps 1/2 Through Nps 24 Metric/inch Standard
AS/NZS 5601.1:2010 cites ASME B16.9:2007 Factory-made wrought steel butt-welding fittings
AS/NZS 5601.1:2010 cites ASTM A106-91 Specification for seamless carbon steel pipe for high temperature service
AS/NZS 5601.1:2010 cites ASTM A269 - 08 Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General Service
AS/NZS 5601.1:2010 cites ASTM A53 / A53M - 07 Standard specification for pipe steel black and hot-dipped zinc-coated welded and seamless
AS/NZS 5601.1:2010 cites BS EN 10241:2000 Steel threaded pipe fittings
AS/NZS 5601.1:2010 cites BS 1640-1:1962 Specification for steel butt-welding pipe fittings for the petroleum industry - Part 1: Wrought carbon and ferritic alloy steel fittings
AS/NZS 5601.1:2010 cites BS 1640-3:1968 Specification for steel butt-welding pipe fittings for the petroleum industry - Part 3: Wrought carbon and ferritic alloy steel fittings. Metric units
AS/NZS 5601.1:2010 cites BS 3799:1974 Specification for steel pipe fittings, screwed and socket-welding for the petroleum industry
AS/NZS 5601.1:2010 cites BS 7838:1996 Specification for corrugated stainless steel semi-rigid pipe and associated fittings for low-pressure gas pipework of up to DN 50
AS/NZS 5601.1:2010 cites BS EN 14324:2004 Brazing. Guidance on the application of brazed joints
AS/NZS 5601.1:2010 cites BS EN 1759.1:2004 Flanges and their joints. Circular flanges for pipes, valves, fittings and accessories, class-designated. Steel flanges, NPS 1/2 to 24.
AS/NZS 5601.1:2010 cites ISO 17484-1:2006 Plastics piping systems - Multilayer pipe systems for indoor gas installations with a maximum operating pressure up to and including 5 bar (500 kPa) - Part 1: Specifications for systems