AS 1397-2011 Continuous hot-dip metallic coated steel sheet and strip - Coatings of zinc and zinc alloyed with aluminium and magnesium
- Abbreviation
- AS 1397-2011
- Amendment
- A1:2012 - incorporated
- Valid from
- 15/09/2011
- Information provider
- Intertek Inform,
- Author
- Standards Australia
- Information type
- Australian Standard,
- Format
- PDF, HARD COPY,
Description
This Standard specifies requirements for continuously hot-dip metallic coated sheet steel and strip supplied in thicknesses up to and including 5.0 mm.
Scope
Requirements for product conformity to this Standard are given in Appendix B.
Requirements covered in this Standard are as follows:
- Formability grades of steel.
- Structural grades of steel.
- Classes of zinc coating, including differential coatings.
- Classes of zinc coating converted to zinc/iron alloy.
- Classes of zinc/aluminium coatings.
- Classes of zinc/aluminium/magnesium alloy coating.
- Classes of aluminium/zinc alloy coating.
- Classes of aluminium/zinc/magnesium alloy coating.
- Surface finish.
Advice and recommendations on information to be supplied by the purchaser at the time of enquiry or order are contained in Appendix A.
The specified requirements apply to the full length and full width of the product supplied, unless otherwise indicated. Within the description of the classes of coatings, the majority element present is listed first, followed by the next major element and followed by a third element if appropriate.
This resource is cited by:
AS 1397-2011 Continuous hot-dip metallic coated steel sheet and strip - Coatings of zinc and zinc alloyed with aluminium and magnesium
This document is CITED BY:
-
B1/AS3 (Amd 19) (First edition, Amendment 19)
AS 1397-2011 is cited by Acceptable Solution B1/AS3: Small Chimneys from 28/11/2019
-
B1/AS3 (Amd 20) (First edition, Amendment 20)
AS 1397-2011 is cited by Acceptable Solution B1/AS3: Small Chimneys from 28/11/2019
-
B1/AS3 (Amd 21) (First Edition, Amendment 21)
AS 1397-2011 is cited by Acceptable Solution B1/AS3: Small Chimneys from 28/11/2019
-
E1/AS1 (Amd 11) (First Edition, Amendment 11.)
AS 1397-2011 is cited by Acceptable Solution E1/AS1: Surface Water from 5/11/2020
-
E2/AS1 (Amd 7) (Third Edition, Amendment 7)
AS 1397-2011 is cited by Acceptable Solution E2/AS1: External Moisture from 14/02/2014
-
E2/AS1 (Amd 10) (Third Edition, Amendment 10)
AS 1397-2011 is cited by Acceptable Solution E2/AS1: External Moisture from 14/02/2014
-
E2/AS1 (Amd 9) (Third Edition, Amendment 9)
AS 1397-2011 is cited by Acceptable Solution E2/AS1: External Moisture from 14/02/2014
-
E2/AS1 (Amd 8) (Third Edition, Amendment 8)
AS 1397-2011 is cited by Acceptable Solution E2/AS1: External Moisture from 14/02/2014
-
E2/AS1 (Amd 6) (Third Edition, Amendment 6)
AS 1397-2011 is cited by Acceptable Solution E2/AS1: External Moisture from 14/02/2014
-
AS 4254.2-2012
AS 1397-2011 is cited by AS 4254.2-2012 Ductwork for air-handling systems in buildings. Part 2: Rigid duct
-
AS/NZS 1554.1:2014
AS 1397-2011 is cited by AS/NZS 1554.1:2014 Structural steel welding - Part 1: Welding of steel structures
-
AS/NZS 2327:2017
AS 1397-2011 is cited by AS/NZS 2327:2017 Composite structures - Composite steel-concrete construction in buildings
-
AS/NZS 2728:2013
AS 1397-2011 is cited by AS/NZS 2728:2013 Prefinished/prepainted sheet metal products for interior/exterior building applications - Performance requirements
-
AS/NZS 3500.1:2015
AS 1397-2011 is cited by AS/NZS 3500.1:2015 Plumbing and drainage - Part 1: Water services
-
AS/NZS 3500.1:2018
AS 1397-2011 is cited by AS/NZS 3500.1:2018 Plumbing and drainage Part 1: Water services
-
AS/NZS 3500.4:2015
AS 1397-2011 is cited by AS/NZS 3500.4:2015 Plumbing and drainage - Heated water services
-
AS/NZS 3500.4:2018
AS 1397-2011 is cited by AS/NZS 3500.4:2018 Plumbing and drainage Part 4: Heated water services
-
AS/NZS 5131:2016
AS 1397-2011 is cited by AS/NZS 5131:2016 Structural steelwork - Fabrication and erection
-
AS/NZS 5601.1:2013
AS 1397-2011 is cited by AS/NZS 5601.1:2013 Gas installations - General installations
-
NASH Standard Part 1:2016
AS 1397-2011 is cited by NASH Standard Part 1:2016 Design Criteria - Alternative Solution
-
NASH Standard Part 2:2019
AS 1397-2011 is cited by NASH Standard Part 2:2019 Light Steel Framed Buildings.
-
SNZ TS 3404:2018
AS 1397-2011 is cited by SNZ TS 3404:2018 Durability requirements for steel structures and components - SPONSORED
This resource cites:
AS 1397-2011 Continuous hot-dip metallic coated steel sheet and strip - Coatings of zinc and zinc alloyed with aluminium and magnesium
This document CITES:
AS 1397-2011 cites AS/NZS 1050.14:1994 Methods for the analysis of iron and steel - Part 14: Determination of manganese in iron and steel - Titrimetric method
AS 1397-2011 cites AS/NZS 1050.16:1994 Methods for the analysis of iron and steel - Part 16: Determination of sulfur content - Infrared absorption method after combustion in an induction furnace
AS 1397-2011 cites AS/NZS 1050.18:1994 (R2016) Methods for the analysis of iron and steel - Part 18: Determination of phosphorus - Spectrophotometric method
AS 1397-2011 cites AS/NZS 1050.1:1996 (R2016) Methods for the analysis of iron and steel - Part 1: Sampling iron and steel for chemical analysis
AS 1397-2011 cites AS/NZS 1050.20:1994 (R2016) Methods for the analysis of iron and steel - Part 20: Determination of magnesium content - Flame atomic absorption spectrometric method
AS 1397-2011 cites AS/NZS 1050.21:1994 (R2016) Methods for the analysis of iron and steel - Part 21: Determination of cobalt content - Spectrophotometric method
AS 1397-2011 cites AS/NZS 1050.24:1994 (R2016) Methods for the analysis of iron and steel - Part 24: Determination of aluminium content - Spectrophotometric method
AS 1397-2011 cites AS/NZS 1050.26:1994 (R2016) Methods for the analysis of iron and steel - Part 26: Silicon in iron and steel - Spectrophotometric method
AS 1397-2011 cites AS/NZS 1050.27:1994 (R016) Methods for the analysis of iron and steel - Part 27: Determination of titanium content - Spectrophotometric method
AS 1397-2011 cites AS/NZS 1050.28:1994 (R2016) Methods for the analysis of iron and steel - Part 28: Vanadium in steel - Potentiometric method
AS 1397-2011 cites AS/NZS 1050.2:1994 (R2016) Methods for the analysis of iron and steel - Part 2: Determination of carbon content - Gravimetric method
AS 1397-2011 cites AS/NZS 1050.30:1994 Methods for the analysis of iron and steel - Part 30: Determination of boron content - Curcumin spectrophotometric method
AS 1397-2011 cites AS/NZS 1050.31:1994 (R206) Methods for the analysis of iron and steel - Part 31: Determination of niobium content - PAR spectrometric method
AS 1397-2011 cites AS/NZS 1050.32:1994 (R2016) Methods for the analysis of iron and steel - Part 32: Determination of carbon content - Infrared method
AS 1397-2011 cites AS/NZS 1050.37:1994 (R2016) Methods for the analysis of iron and steel - Part 37: Determination of copper content - Flame atomic absorption spectrometric method
AS 1397-2011 cites AS/NZS 1050.38:1994 (R2016) Methods for the analysis of iron and steel - Part 38: Determination of vanadium content - Flame atomic absorption spectrometric method
AS 1397-2011 cites AS/NZS 1050.39:1994 (R2016) Methods for the analysis of iron and steel - Part 39: Determination of chromium content - Flame atomic absorption spectrometric method
AS 1397-2011 cites AS/NZS 1050.6:1995 (R2016) Methods for the analysis of iron and steel - Part 6: Determination of tin content - Flame atomic absorption spectrometric method
AS 1397-2011 cites AS/NZS 1050.8:1994 (R2016) Methods for the analysis of iron and steel - Determination of manganese content (spectrophotometric method)
AS 1397-2011 cites AS/NZS 1365:1996 (R2016) Tolerances for flat-rolled steel products
AS 1397-2011 cites AS 1391-2007 (R2017) Metallic materials - Tensile testing at ambient temperature
AS 1397-2011 cites AS 2331.2.1-2001 (R2017) Methods of test for metallic and related coatings - Method 2.1: Local thickness tests - Tests for average coating mass per unit area or for thickness - Dissolution methods - Strip and weigh and analytical
AS 1397-2011 cites AS 2331.2.3-2001 (R2017) Methods of test for metallic and related coatings - Method 2.3: Local thickness tests - Tests for average coating mass per unit area or for thickness - Hydrogen evolution method for zinc coatings
AS 1397-2011 cites AS 2505.1-2004 (R2017) Metallic materials - Sheet, strip and plate - Bend tests
AS 1397-2011 cites ASTM A754 / A754M - 08 Standard Test Method for Coating Weight (Mass) of Metallic Coatings on Steel by X-Ray Fluorescence
AS 1397-2011 cites ISO 7966:1993 Acceptance control charts