BS EN 1111:2017 Sanitary tapware. Thermostatic mixing valves (PN 10). General technical specification
- Abbreviation
- BS EN 1111:2017
- Valid from
- 22/08/2017
- Information provider
- Standards New Zealand,
- Author
- British Standards Institution, European Standardization Organizations
- Information type
- British Standard,
- Format
- PDF, HARD COPY,
Description
This Standard discusses sanitary tapware. It specifies general construction, performance, and material requirements for PN 10 thermostatic mixing valves (TMV) and includes test methods for the verification of mixed water temperature performance at the point of use below 45 °C.
This Standard applies to valves intended for use on sanitary appliances in kitchens, washrooms (incl. all rooms with sanitary tapware, e.g., toilets and cloakrooms), and bathrooms operating under specified conditions.
This Standard allows TMVs to supply a single outlet or a small number of outlets in a “domestic” application (e.g., one valve controlling a shower, bath, basin, and/or bidet), excluding valves specifically designed for supplying a large number of outlets (i.e., for institutional use).
The tests described are type tests (laboratory tests) and not quality control tests carried out during manufacture.
Scope
The PN 10 thermostatic mixing valves (TMV) are used to provide anti-scald protection for children, elderly, and disabled persons the mixed water temperature needs to be set at a suitable bathing temperature (body temperature approximately 38 °C) as children are at risk of scalding at lower temperatures than adults. This does not obviate the need for supervision of young children during bathing.
This Standard provides general construction, performance, and material requirements for PN 10 thermostatic mixing valves (TMV) and includes test methods for the verification of mixed water temperature performance at the point of use below 45 °C. This does not exclude the selection of higher temperatures where available.
This Standard helps manufacture sanitary tapware with thermostatic mixing valves (PN 10) that meets the requirements of this technical standard and gives your customer a better user experience.
This resource is cited by:
BS EN 1111:2017 Sanitary tapware. Thermostatic mixing valves (PN 10). General technical specification
This document is CITED BY:
-
G12/AS1 (Amd 13) (Third Edition, Amendment 13)
BS EN 1111:2017 is cited by Acceptable Solution G12/AS1: Water Supplies from 2/11/2023
This resource cites:
BS EN 1111:2017 Sanitary tapware. Thermostatic mixing valves (PN 10). General technical specification
This document CITES:
BS EN 1111:2017 cites BS EN 1057:2006+A1:2010 Copper and copper alloys. Seamless, round copper tubes for water and gas in sanitary and heating applications
BS EN 1111:2017 cites BS EN 1112:2008 Sanitary tapware. Shower outlets for sanitary tapware for water supply systems type 1 and type 2. General technical specification
BS EN 1111:2017 cites BS EN 1113:2015 - TC Sanitary tapware. Shower hoses for sanitary tapware for water supply systems of type 1 and type 2. General technical specification
BS EN 1111:2017 cites BS EN 13618:2016 - TC Flexible hose assemblies in drinking water installations. Functional requirements and test methods
BS EN 1111:2017 cites BS EN 13959:2004 Anti-pollution check valves. DN 6 to DN 250 inclusive Family E, type A, B, C, and D
BS EN 1111:2017 cites BS EN 14506:2005 Devices to prevent pollution by backflow of potable water. Automatic diverter. Family H, type C
BS EN 1111:2017 cites BS EN 16145:2012 Sanitary tapware. Extractable outlets for sink and basin mixers. General technical specification
BS EN 1111:2017 cites BS EN 1717:2000 Protection against pollution of potable water in water installations and general requirements of devices to prevent pollution by backflow
BS EN 1111:2017 cites BS EN 200:2008 Sanitary tapware. Single taps and combination taps for water supply systems of type 1 and type 2. General technical specification
BS EN 1111:2017 cites BS EN 246:2003 Sanitary tapware. General specifications for flow rate regulators
BS EN 1111:2017 cites BS EN 248:2002 Sanitary tapware. General specification for electrodeposited coatings of Ni-Cr
BS EN 1111:2017 cites BS EN 60584-1:2013 Thermocouples. EMF specifications and tolerances
BS EN 1111:2017 cites BS EN 60584-3:2008 Thermocouples - Extension and compensating cables. Tolerances and identification system
BS EN 1111:2017 cites BS EN ISO 228-1:2003 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation
BS EN 1111:2017 cites BS EN ISO 3822-1:1999 +A1:2008 Acoustics. Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 1: Method of measurement
BS EN 1111:2017 cites BS EN ISO 3822-1:1999 +A1:2008 Acoustics. Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 1: Method of measurement
BS EN 1111:2017 cites BS EN ISO 3822-2:1996 Acoustics. Laboratory tests on noise emission from appliances and equipment used in water supply installations - Part 2: Mounting and operating conditions for draw-off taps and mixing valves
BS EN 1111:2017 cites BS EN ISO 3822-3:1997 +A1:2009 Acoustics. Laboratory tests on noise emission from appliances and equipment used in water supply installations. Mounting and operating conditions for in-line valves and appliances
BS EN 1111:2017 cites BS EN ISO 3822-3:1997 +A1:2009 Acoustics. Laboratory tests on noise emission from appliances and equipment used in water supply installations. Mounting and operating conditions for in-line valves and appliances
BS EN 1111:2017 cites BS EN ISO 5167-1:2003 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 1: General principles and requirements
BS EN 1111:2017 cites BS EN ISO 5167-1:2003 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 1: General principles and requirements
BS EN 1111:2017 cites IEC 60584-1:2013 Thermocouples – Part 1: EMF specifications and tolerances
BS EN 1111:2017 cites IEC 60584-3:2007 Thermocouples - Part 3: Extension and compensating cables - Tolerances and identification system
BS EN 1111:2017 cites ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation