BS EN 246:2003 Sanitary tapware. General specifications for flow rate regulators

Abbreviation
BS EN 246:2003
Valid from
3/09/2003

Information provider
Standards New Zealand,
Author
British Standards Institution, European Standardization Organizations
Information type
British Standard,
Format
PDF, HARD COPY,


Description

This European Standard specifies:
  •  the dimensional, mechanical, hydraulic and acoustic characteristics with which flow rate regulators should comply;
  •  the procedures for testing these characteristics.
This European Standard is applicable to:
  •  flow rate regulators intended to be mounted on tapware used with sanitary appliances in toilets, washrooms and kitchens (single taps, combination tap assemblies, mechanical mixing valves, thermostatic mixing valves);
  •  flow rate regulators used under the following pressure and temperature conditions:
Table 1  Conditions for the use of flow rate regulators
Limits of use Recommended limits for correct operation Dynamic Pressure 0,05 MPa  P ≤ 0,5 MPa
(0,5 bar  P ≤ 5 bar)
0,1 MPa  P ≤ 0,5 MPa
(1 bar  P ≤ 5 bar)
Temperature ≤ 70 °C ≤ 65 °C
Flow rate regulators can only be connected downstream of the obturator of the tap.

For assistance with locating previous versions, please contact the information provider.
View on Information Provider website
For assistance with locating previous versions, please contact the information provider.
This resource is cited by:

BS EN 246:2003 Sanitary tapware. General specifications for flow rate regulators

This document is CITED BY:

BS EN 246:2003 Sanitary tapware. General specifications for flow rate regulators

Description

This European Standard specifies:
  •  the dimensional, mechanical, hydraulic and acoustic characteristics with which flow rate regulators should comply;
  •  the procedures for testing these characteristics.
This European Standard is applicable to:
  •  flow rate regulators intended to be mounted on tapware used with sanitary appliances in toilets, washrooms and kitchens (single taps, combination tap assemblies, mechanical mixing valves, thermostatic mixing valves);
  •  flow rate regulators used under the following pressure and temperature conditions:
Table 1  Conditions for the use of flow rate regulators
Limits of use Recommended limits for correct operation Dynamic Pressure 0,05 MPa  P ≤ 0,5 MPa
(0,5 bar  P ≤ 5 bar)
0,1 MPa  P ≤ 0,5 MPa
(1 bar  P ≤ 5 bar)
Temperature ≤ 70 °C ≤ 65 °C
Flow rate regulators can only be connected downstream of the obturator of the tap.

View on Information Provider website
BS EN 246:2003 Sanitary tapware. General specifications for flow rate regulators
Description
This European Standard specifies:
  •  the dimensional, mechanical, hydraulic and acoustic characteristics with which flow rate regulators should comply;
  •  the procedures for testing these characteristics.
This European Standard is applicable to:
  •  flow rate regulators intended to be mounted on tapware used with sanitary appliances in toilets, washrooms and kitchens (single taps, combination tap assemblies, mechanical mixing valves, thermostatic mixing valves);
  •  flow rate regulators used under the following pressure and temperature conditions:
Table 1  Conditions for the use of flow rate regulators
Limits of use Recommended limits for correct operation Dynamic Pressure 0,05 MPa  P ≤ 0,5 MPa
(0,5 bar  P ≤ 5 bar)
0,1 MPa  P ≤ 0,5 MPa
(1 bar  P ≤ 5 bar)
Temperature ≤ 70 °C ≤ 65 °C
Flow rate regulators can only be connected downstream of the obturator of the tap.
View on Information Provider website
This resource does not cite any other resources.

BS EN 246:2003 Sanitary tapware. General specifications for flow rate regulators

This resource does not CITE any other resources.
Feedback