AS 3571.1-2009 Plastics piping systems - Glass-reinforced thermoplastics (GRP) systems based on unsaturated polyester (UP) resin. Part 1: Pressure and non-pressure drainage and sewerage (ISO 10467:2004 MOD)
- Abbreviation
- AS 3571.1-2009
- Amendment
- AS 3571.1-2009/Amdt 1-2009
- Valid from
- 27/04/2009
- Information provider
- Intertek Inform,
- Author
- Standards Australia
- Information type
- Australian Standard,
- Format
- PDF, HARD COPY,
Description
This Standards specifies the properties of piping system components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) for drainage or sewerage with or without pressure. Has been reproduced from ISO 10467:2004.
This resource is cited by:
AS 3571.1-2009 Plastics piping systems - Glass-reinforced thermoplastics (GRP) systems based on unsaturated polyester (UP) resin. Part 1: Pressure and non-pressure drainage and sewerage (ISO 10467:2004 MOD)
This document is CITED BY:
-
G13/AS2 (Second Edition, Amendment 6)
AS 3571.1-2009 is cited by Acceptable Solution G13/AS2: Drainage from 10/10/2011
-
G13/AS2 (Second Edition, Amendment 5)
AS 3571.1-2009 is cited by Acceptable Solution G13/AS2: Drainage from 10/10/2011
-
G13/AS2 (Second Edition, Amendment 4)
AS 3571.1-2009 is cited by Acceptable Solution G13/AS2: Drainage from 10/10/2011
-
G13/AS2 (Second Edition, Amendment 7)
AS 3571.1-2009 is cited by Acceptable Solution G13/AS2: Drainage from 10/10/2011
-
G13/AS2 (Second Edition, Amendment 8)
AS 3571.1-2009 is cited by Acceptable Solution G13/AS2: Drainage from 10/10/2011
-
G13/AS2 (Amd 9) (Second Edition, Amendment 9)
AS 3571.1-2009 is cited by Acceptable Solution G13/AS2: Drainage from 10/10/2011
-
G13/AS2 (Amd 10) (Second Edition, Amendment 10)
AS 3571.1-2009 is cited by Acceptable Solution G13/AS2: Drainage from 10/10/2011
-
AS/NZS 3500.2:2015
AS 3571.1-2009 is cited by AS/NZS 3500.2:2015 Plumbing and drainage - Part 2: Sanitary plumbing and drainage
-
AS/NZS 3500.2:2018
AS 3571.1-2009 is cited by AS/NZS 3500.2:2018 Plumbing and drainage Part 2: Sanitary plumbing and drainage
-
AS/NZS 3500.3:2018
AS 3571.1-2009 is cited by AS/NZS 3500.3:2018 Plumbing and drainage Part 3: Stormwater drainage
-
AS/NZS 3500.3:2021
AS 3571.1-2009 is cited by AS/NZS 3500.3:2021 Plumbing and drainage, Part 3: Stormwater drainage
This resource cites:
AS 3571.1-2009 Plastics piping systems - Glass-reinforced thermoplastics (GRP) systems based on unsaturated polyester (UP) resin. Part 1: Pressure and non-pressure drainage and sewerage (ISO 10467:2004 MOD)
This document CITES:
AS 3571.1-2009 cites AS/NZS 4020:2005 Testing of products for use in contact with drinking water
AS 3571.1-2009 cites AS 1646-2007 (R2018) Elastomeric seals for waterworks purposes
AS 3571.1-2009 cites AS 3572.4-2002 (R2016) Plastics - Glass filament reinforced plastics (GRP) - Methods of test - Method 4: Determination of the dimensions of glass filament reinforced plastics pipes
AS 3571.1-2009 cites BS EN 681-1:1996 Elastomeric seals. Material requirements for pipe joint seals used in water and drainage applications - Part 1: Vulcanized rubber
AS 3571.1-2009 cites BS EN 681-2:2000 Elastomeric Seals - Materials Requirements For Pipe Joint Seals Used In Water And Drainage Applications - Part 2: Thermoplastic Elastomers
AS 3571.1-2009 cites ISO 10466:1997 Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Test method to prove the resistance to initial ring deflection
AS 3571.1-2009 cites ISO 10468:2003 Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the long-term specific ring creep stiffness under wet conditions and calculation of the wet creep factor
AS 3571.1-2009 cites ISO 10471:2003 Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the long-term ultimate bending strain and the long-term ultimate relative ring deflection under wet conditions
AS 3571.1-2009 cites ISO 10928:1997 Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Methods for regression analysis and their use
AS 3571.1-2009 cites ISO 10952:2008 Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Determination of the resistance to chemical attack for the inside of a section in a deflected condition
AS 3571.1-2009 cites ISO 11922-1:1997 Thermoplastics pipes for the conveyance of fluids - Dimensions and tolerances Part 1: Metric series
AS 3571.1-2009 cites ISO 14828:2003 Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the long-term specific ring relaxation stiffness under wet conditions and calculation of the wet relaxation factor
AS 3571.1-2009 cites ISO 15306:2003 Glass-reinforced thermosetting plastics (GRP) pipes - Determination of the resistance to cyclic internal pressure
AS 3571.1-2009 cites ISO 161-1:1996 Thermoplastics pipes for the conveyance of fluids - Nominal outside diameters and nominal pressures - Part 1: Metric series
AS 3571.1-2009 cites ISO 2531:1998 Ductile iron pipes, fittings, accessories and their joints for water or gas applications
AS 3571.1-2009 cites ISO 3126:2005 Plastics piping systems - Plastics components - Determination of dimensions
AS 3571.1-2009 cites ISO 4200:1991 Plain end steel tubes, welded and seamless - General tables of dimensions and masses per unit length
AS 3571.1-2009 cites ISO 527-4:1997 Plastics - Determination of tensile properties - Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites
AS 3571.1-2009 cites ISO 527-5:1997 Plastics - Determination of tensile properties Part 5: Test conditions for unidirectional fibre-reinforced plastic composites
AS 3571.1-2009 cites ISO 7432:2002 Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods to prove the design of locked socket-and-spigot joints, including double-socket joints, with elastomeric seals
AS 3571.1-2009 cites ISO 75-2:2004 Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite
AS 3571.1-2009 cites ISO 7509:2000 Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Determination of time to failure under sustained internal pressure
AS 3571.1-2009 cites ISO 7685:1998 Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Determination of initial specific ring stiffness
AS 3571.1-2009 cites ISO 8483:2003 Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods to prove the design of bolted flange joints
AS 3571.1-2009 cites ISO 8513:2000 Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Determination of longitudinal tensile properties
AS 3571.1-2009 cites ISO 8521:1998 Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the apparent initial circumferential tensile strength
AS 3571.1-2009 cites ISO 8533:2003 Plastics piping systems for pressure and non-pressure drainage and sewerage — Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin — Test methods to prove the design of cemented or wrapped joints
AS 3571.1-2009 cites ISO 8639:2000 Glass-reinforced thermosetting plastics (GRP) pipes and fittings — Test methods for leaktightness of flexible joints
AS 3571.1-2009 cites JIS A 5350:1991 Fiberglass reinforced plastic mortar pipes