AS/NZS 1546.1:2008 On-site domestic wastewater treatment units: Septic tanks
- Abbreviation
- AS/NZS 1546.1:2008
- Valid from
- 28/05/2008
- Information provider
- Standards New Zealand,
- Author
- Standards New Zealand, Standards Australia
- Information type
- New Zealand Standard,
- Format
- PDF, HARD COPY,
Description
This Standard covers the manufacture of septic tanks and their associated fittings for the treatment of domestic wastewater only.
Scope
This Standard covers the manufacture of septic tanks and their associated fittings for the treatment of domestic wastewater only. This range of tanks typically is designed to cater for:
- (a) All-waste (Blackwater and Greywater);
- (b) Blackwater only;
- (c) Greywater (with or without kitchen waste included) only; and
- (d) Holding tanks (collection wells) and pump wells.
Septic tanks covered by this Standard are suitable for a flow of domestic wastewater of up to 14,000 litres per week
This resource is cited by:
AS/NZS 1546.1:2008 On-site domestic wastewater treatment units: Septic tanks
This document is CITED BY:
-
G14/VM1 (Amd 6) (Second Edition, Amendment 6)
AS/NZS 1546.1:2008 is cited by Verification Method G14/VM1: Industrial Liquid Waste from 10/10/2011
-
G14/VM1 (Amd 5) (Second Edition, Amendment 5)
AS/NZS 1546.1:2008 is cited by Verification Method G14/VM1: Industrial Liquid Waste from 10/10/2011
-
G14/VM1 (Second Edition, Amendment 4)
AS/NZS 1546.1:2008 is cited by Verification Method G14/VM1: Industrial Liquid Waste from 10/10/2011
-
AS/NZS 1547:2012
AS/NZS 1546.1:2008 is cited by AS/NZS 1547:2012 On-site domestic wastewater management
-
AS/NZS 3500.2:2015
AS/NZS 1546.1:2008 is cited by AS/NZS 3500.2:2015 Plumbing and drainage - Part 2: Sanitary plumbing and drainage
-
AS/NZS 3500.2:2018
AS/NZS 1546.1:2008 is cited by AS/NZS 3500.2:2018 Plumbing and drainage Part 2: Sanitary plumbing and drainage
-
DoC backcountry hut manual 2009 (Version 4)
AS/NZS 1546.1:2008 is cited by Hut procurement manual for backcountry huts
This resource cites:
AS/NZS 1546.1:2008 On-site domestic wastewater treatment units: Septic tanks
This document CITES:
AS/NZS 1546.1:2008 cites AS/NZS 1547:2000 On-site domestic wastewater management
AS/NZS 1546.1:2008 cites AS/NZS 3500.2:2003 Plumbing and drainage - Sanitary plumbing and drainage
AS/NZS 1546.1:2008 cites AS/NZS 4671:2001 Steel reinforcing materials
AS/NZS 1546.1:2008 cites AS/NZS 4766:2006 Polyethylene storage tanks for water and chemicals
AS/NZS 1546.1:2008 cites NZS 3104:2003 Specification for concrete production
AS/NZS 1546.1:2008 cites NZS 3106:1986 Code of practice for concrete structures for the storage of liquids. - SPONSORED
AS/NZS 1546.1:2008 cites NZS 3109:1997 Concrete construction - SPONSORED
AS/NZS 1546.1:2008 cites NZS 3112.2:1986 Methods of test for concrete - Tests relating to the determination of strength of concrete - SPONSORED
AS/NZS 1546.1:2008 cites NZS 3113:1979 Specification for chemical admixtures for concrete
AS/NZS 1546.1:2008 cites NZS 3121:1986 Specification for water and aggregate for concrete
AS/NZS 1546.1:2008 cites NZS 3122:1995 Specification for Portland and blended cements (General and special purpose)
AS/NZS 1546.1:2008 cites NZS ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories
AS/NZS 1546.1:2008 cites AS 1012.14-1991 Methods of testing concrete - Method for securing and testing cores from hardened concrete for compressive strength
AS/NZS 1546.1:2008 cites AS 1012.8.1-2000 Methods of testing concrete. Method for making and curing concrete - Compression and indirect tensile test specimens
AS/NZS 1546.1:2008 cites AS 1012.8.2-2000 Methods of testing concrete. Method for making and curing concrete - Flexure test specimens
AS/NZS 1546.1:2008 cites AS 1012.9-1999 Methods of testing concrete - Part 9: Determination of the compressive strength of concrete specimens
AS/NZS 1546.1:2008 cites AS 1379-2007 (R2017) Specification and supply of concrete
AS/NZS 1546.1:2008 cites AS 1478.1-2000 (R2018) Chemical admixtures for concrete, mortar and grout - Admixtures for concrete
AS/NZS 1546.1:2008 cites AS 1597.1-1974 Precast reinforced concrete box culverts - Part 1: Small culverts (not exceeding 1200 mm width and 900 mm depth)
AS/NZS 1546.1:2008 cites AS 2738-2000 (R2018) Copper and copper alloys - Compositions and designations of refinery products, wrought products, ingots and castings
AS/NZS 1546.1:2008 cites AS 2758.1-1998 Aggregates and rock for engineering purposes
AS/NZS 1546.1:2008 cites AS 3600-2001 Concrete structures
AS/NZS 1546.1:2008 cites AS 3972-1997 General purpose and blended cements
AS/NZS 1546.1:2008 cites AS ISO/IEC 17025-2005 (R2016) General requirements for the competence of testing and calibration laboratories
AS/NZS 1546.1:2008 cites Resource Management Act 1991
AS/NZS 1546.1:2008 cites The Building Act 2004
AS/NZS 1546.1:2008 cites ASTM A240/A240M-07 Standard specification for chromium and chromium-nickel stainless steel plate sheet and strip for pressure vessels and general applications
AS/NZS 1546.1:2008 cites ASTM C1609 / C1609M - 06 Standard Test Method for Flexural Performance of Fiber-Reinforced Concrete (Using Beam With Third-Point Loading)
AS/NZS 1546.1:2008 cites ASTM D3029-95 Test methods for impact resistance of flat rigid plastic specimens by means of a tup (falling weight)
AS/NZS 1546.1:2008 cites ASTM D4097 - 01 Standard Specification for Contact-Molded Glass-Fiber-Reinforced Thermoset Resin Corrosion-Resistant Tanks
AS/NZS 1546.1:2008 cites BS 3396-3:1987 Woven glass fibre fabrics for plastics reinforcement - Part 3: Specification for finished fabrics for use with polyester resin systems
AS/NZS 1546.1:2008 cites BS 3749:1991 Specification for E glass fibre woven roving fabrics for the reinforcement of polyester and epoxy resin systems
AS/NZS 1546.1:2008 cites BS EN 13923:2005 Filament-wound FRP pressure vessels. Materials design manufacturing and testing
AS/NZS 1546.1:2008 cites BS EN 14020-3:2002 Reinforcements - Part 3: Specification for textile glass rovings - Specific requirements
AS/NZS 1546.1:2008 cites BS EN 14118-3:2003 Reinforcement - Part 3: Specifications for textile glass mats (chopped strand and continuous filament mats). Specific requirements
AS/NZS 1546.1:2008 cites HB 18.28-2005 Conformity assessment - Guidance on a third-party certification system for products
AS/NZS 1546.1:2008 cites ISO 1172:1996 - Textile-glass-reinforced plastics - Prepregs, moulding compounds and laminates - Determination of the textile-glass and mineral-filler content - Calcination methods
AS/NZS 1546.1:2008 cites ISO 1268-4:2005 Fibre-reinforced plastics - Methods of producing test plates - Part 4: Moulding of prepregs
AS/NZS 1546.1:2008 cites ISO 14125:1998 (R2013) Fibre-reinforced plastic composites - Determination of flexural properties
AS/NZS 1546.1:2008 cites ISO 179-2:1997 Plastics - Determination of Charpy impact properties - Part 2: Instrumented impact test
AS/NZS 1546.1:2008 cites ISO 527-4:1997 Plastics - Determination of tensile properties - Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites
AS/NZS 1546.1:2008 cites ISO 62:2008 (R2016) Plastics - Determination of water absorption
AS/NZS 1546.1:2008 cites ISO 75-2:2004 Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite
AS/NZS 1546.1:2008 cites ISO 75-3:2004 (R2017) Plastics - Determination of temperature of deflection under load - Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics
AS/NZS 1546.1:2008 cites Building Regulations 1992