AS 2050-2002 Installation of roof tiles
- Abbreviation
- AS 2050-2002
- Amendment
- 2
- Valid from
- 30/10/2002
- Information provider
- Intertek Inform,
- Author
- Standards Australia
- Information type
- Australian Standard,
- Format
- PDF, HARD COPY,
Description
This Standard sets out requirements for the placement and installing of roof tiles of the types specified in AS 2049.
The installation methods described in this Standard apply only to tiled roofs of buildings that are intended for domestic, commercial or light industrial purposes for wind classifications N1-N4 and C1-C3 inclusive. This Standard applies only to roofs with a pitch of 15 or greater.
Scope
NOTES:
- This Standard does not restrict the use of other installing and fastening methods or materials where it can be shown that they are not inferior to the performance achieved by the materials and methods described herein.
- Where it is intended to install tiles to roofs with a pitch of less than 15, the tile manufacturers advice should be sought to determine weatherproofing requirements.
- The type of roof construction described in this Standard may not be adequate to resist wind forces in cases where the height of the eaves is more than 15 m above the mean surrounding ground level. In such cases, or in areas where cyclones or high winds are known to occur, the installing and fastening methods and sarking recommendations given in Appendix A are recommended.
- Appendix B includes information on the data normally provided by the specifier and the tile manufacturer, and on the work normally carried out as part of the tiling operation.
This resource is cited by:
AS 2050-2002 Installation of roof tiles
This document is CITED BY:
-
E2/AS1 (Amd 7) (Third Edition, Amendment 7)
AS 2050-2002 is cited by Acceptable Solution E2/AS1: External Moisture from 1/02/2005
-
E2/AS1 (Amd 6) (Third Edition, Amendment 6)
AS 2050-2002 is cited by Acceptable Solution E2/AS1: External Moisture from 1/02/2005
-
E2/AS1 (Amd 5, Errata 2) (Third Edition, Amendment 5, Errata 2)
AS 2050-2002 is cited by Acceptable Solution E2/AS1: External Moisture from 1/02/2005
-
E2/AS1 (Amd 5) (Third Edition, Amendment 5)
AS 2050-2002 is cited by Acceptable Solution E2/AS1: External Moisture from 1/02/2005
-
E2/AS1 (Amd 4) (Third Edition, Amendment 4)
AS 2050-2002 is cited by Acceptable Solution E2/AS1: External Moisture from 1/02/2005
-
E2/AS1 (Amd 8) (Third Edition, Amendment 8)
AS 2050-2002 is cited by Acceptable Solution E2/AS1: External Moisture from 1/02/2005
-
E2/AS1 (Amd 9) (Third Edition, Amendment 9)
AS 2050-2002 is cited by Acceptable Solution E2/AS1: External Moisture from 1/02/2005
-
E2/AS1 (Amd 10) (Third Edition, Amendment 10)
AS 2050-2002 is cited by Acceptable Solution E2/AS1: External Moisture from 1/02/2005
-
E2/VM1 (Amd 4) (Third Edition, Amendment 4)
AS 2050-2002 is cited by Verification Method E2/VM1: External Moisture from 1/07/2004
-
AS 2049-2002 (R2015)
AS 2050-2002 is cited by AS 2049-2002 (R2015) Roof tiles
-
AS/NZS 3500.3:2018
AS 2050-2002 is cited by AS/NZS 3500.3:2018 Plumbing and drainage Part 3: Stormwater drainage
-
NASH Building Envelope Solutions: 2019
AS 2050-2002 is cited by NASH Building Envelope Solutions: 2019 - Light Steel Framed Buildings.
This resource cites:
AS 2050-2002 Installation of roof tiles
This document CITES:
AS 2050-2002 cites AS/NZS 1170.1:2002 (R2016) Structural Design Actions - Permanent, imposed and other actions
AS 2050-2002 cites AS/NZS 1170.2:2002 Structural Design Actions - Wind Actions
AS 2050-2002 cites AS/NZS 3500.3:2003 Plumbing and drainage - Part 3: Stormwater drainage
AS 2050-2002 cites AS/NZS 4200.1:1994 Pliable building membranes and underlays - Materials
AS 2050-2002 cites AS/NZS 4200.2:1994 Pliable building membranes and underlays - Part 2: Installation requirements
AS 2050-2002 cites AS 1170.3-1990 Minimum design loads on structures (known as the SAA Loading Code) Snow loads
AS 2050-2002 cites AS 1397-2001 Steel sheet and strip - Hot-dipped zinc-coated or aluminium/zinc-coated
AS 2050-2002 cites AS 1478.1-2000 (R2018) Chemical admixtures for concrete, mortar and grout - Admixtures for concrete
AS 2050-2002 cites AS 1684.2-1999 Residential timber-framed construction Part 2: Non-cyclonic areas
AS 2050-2002 cites AS 1684.3-1999 Residential timber-framed construction Part 3: Cyclonic areas
AS 2050-2002 cites AS 1720.1-1997 Timber structures - Part 1: Design methods
AS 2050-2002 cites AS 2049-2002 (R2015) Roof tiles
AS 2050-2002 cites AS 2334-1980 (R2015) Steel nails - Metric series
AS 2050-2002 cites AS 2701-2001 (R2015) Methods of sampling and testing mortar for masonry constructions
AS 2050-2002 cites AS 2758.1-1998 Aggregates and rock for engineering purposes
AS 2050-2002 cites AS 3566.1-2002 (R2015) Self-drilling screws for the building and construction industries - Part 1: General requirements and mechanical properties
AS 2050-2002 cites AS 3566.2-2002 Self-drilling screws for the building and construction industries. Part 2: Corrosion resistance requirements
AS 2050-2002 cites AS 3700-2001 Masonry structures
AS 2050-2002 cites AS 3972-1997 General purpose and blended cements
AS 2050-2002 cites AS 4046.8-2002 Methods of testing roof tiles - Method 8: Adhesive mechanical fastener (flexible pointing)
AS 2050-2002 cites AS 4046.9-2002 (R2015) Methods of testing roof tiles. Part 9: Determination of dynamic weather resistance
AS 2050-2002 cites AS 4055-1992 Wind loads for housing
AS 2050-2002 cites BS EN 12878:1999 Pigments for the colouring of building materials based on cement and/or lime. Specifications and methods of test
AS 2050-2002 cites NASH Standard - Residential and Low-Rise Steel Framing Part 1 2010 Design Criteria