BS EN 1759.1:2004 Flanges and their joints. Circular flanges for pipes, valves, fittings and accessories, class-designated. Steel flanges, NPS 1/2 to 24.
- Abbreviation
- BS EN 1759-1:2004
- Valid from
- 1/01/2004
- Information provider
- Standards New Zealand
- Author
- British Standards Institution
- Information type
- British Standard
Description
This Standard for a single system of flanges specifies requirements for circular steel flanges in Class designations Class 150 to Class 2 500 and nominal sizes from NPS ½ to NPS 24.
This Standard specifies the flange types and their facings, dimensions, tolerances, threading, bolt sizes, flange jointing face surface finish, marking, materials, and pressure/temperature ratings.
Scope
This Standard for a single system of flanges specifies requirements for circular steel flanges in Class designations Class 150 to Class 2 500 and nominal sizes from NPS ½ to NPS 24.
This Standard specifies the flange types and their facings, dimensions, tolerances, threading, bolt sizes, flange jointing face surface finish, marking, materials, and pressure/temperature ratings.
This Standard does not apply to flanges made from bar stock by turning, or to flanges of types 11, 12, 13, 14 and 15 made from plate material.
This resource is cited by:
BS EN 1759.1:2004 Flanges and their joints. Circular flanges for pipes, valves, fittings and accessories, class-designated. Steel flanges, NPS 1/2 to 24.
This document is CITED BY:
-
E1/AS1 (Amd 10) (First Edition, Amendment 10)
BS EN 1759-1:2004 is cited by Acceptable Solution E1/AS1: Surface Water from 30/09/2010
-
E1/AS1 (Amd 9) (First Edition, Amendment 9)
BS EN 1759-1:2004 is cited by Acceptable Solution E1/AS1: Surface Water from 30/09/2010
-
E1/AS1 (Amd 8) (First Edition, Amendment 8)
BS EN 1759-1:2004 is cited by Acceptable Solution E1/AS1: Surface Water from 30/09/2010
-
E1/AS1 (Amd 11) (First Edition, Amendment 11.)
BS EN 1759-1:2004 is cited by Acceptable Solution E1/AS1: Surface Water from 30/09/2010
-
E1/AS1 (Amd 12) (First Edition, Amendment 12.)
BS EN 1759-1:2004 is cited by Acceptable Solution E1/AS1: Surface Water from 30/09/2010
-
AS/NZS 5601.1:2010
BS EN 1759-1:2004 is cited by AS/NZS 5601.1:2010 Gas installations - Part 1: General installations
-
AS/NZS 5601.1:2013
BS EN 1759-1:2004 is cited by AS/NZS 5601.1:2013 Gas installations - General installations
This resource cites:
BS EN 1759.1:2004 Flanges and their joints. Circular flanges for pipes, valves, fittings and accessories, class-designated. Steel flanges, NPS 1/2 to 24.
This document CITES:
Other
-
ANSI/ASME B1.20.1:1983
BS EN 1759-1:2004 cites ANSI/ASME B1.20.1:1983 (R2006) Pipe threads general purpose (Inch)
-
ASTM A105/A105M-87
BS EN 1759-1:2004 cites ASTM A105/A105M-87 Standard specification for forgings, carbon steel, for piping components
-
ASTM A182/A182M-00c (Revision 00c)
BS EN 1759-1:2004 cites ASTM A182/A182M-00c Standard Specification for Forged or Rolled Alloy-Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service
-
ASTM A203/A203M-97 (2007)e1 (Revised 2007 -includes editorial correction 'e1')
BS EN 1759-1:2004 cites ASTM A203/A203M-97 (2007)e1 Standard Specification for Pressure Vessel Plates, Alloy Steel, Nickel
-
ASTM A204/A204M-03 (2007) (Revised 2007)
BS EN 1759-1:2004 cites ASTM A204/A204M-03 (2007) Standard Specification for Pressure Vessel Plates, Alloy Steel, Molybdenum
-
ASTM A216/A216M - 93 (1998)
BS EN 1759-1:2004 cites ASTM A216/A216M - 93 (1998) Standard Specification for Steel Castings, Carbon, Suitable for Fusion Welding, for High- Temperature Service
-
ASTM A217 / A217M - 02
BS EN 1759-1:2004 cites ASTM A217 / A217M - 02 Standard Specification for Steel Castings, Martensitic Stainless and Alloy, for Pressure-Containing Parts, Suitable for High-Temperature Service
-
ASTM A240/A240M-02
BS EN 1759-1:2004 cites ASTM A240/A240M-02 Heat resisting chromium and chromium-nickel stainless steel plate sheet and strip for pressure vessels
-
ASTM A325 - 02
BS EN 1759-1:2004 cites ASTM A325 - 02 Standard Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength
-
ASTM A350 / A350M - 02b
BS EN 1759-1:2004 cites ASTM A350 / A350M - 02b Standard Specification for Carbon and Low-Alloy Steel Forgings, Requiring Notch Toughness Testing for Piping Components
-
ASTM A351/A351M-03
BS EN 1759-1:2004 cites ASTM A351/A351M-03 Standard Specification for Castings, Austenitic, Austenitic-Ferritic (Duplex), for Pressure-Containing Parts
-
ASTM A352 / A352M - 03
BS EN 1759-1:2004 cites ASTM A352 / A352M - 03 Standard Specification for Steel Castings, Ferritic and Martensitic, for Pressure-Containing Parts, Suitable for Low-Temperature Service
-
ASTM A387 / A387M - 03
BS EN 1759-1:2004 cites ASTM A387 / A387M - 03 Standard Specification for Pressure Vessel Plates, Alloy Steel, Chromium-Molybdenum
-
ASTM A515 / A515M - 03(2007) (Revised 2007)
BS EN 1759-1:2004 cites ASTM A515 / A515M - 03(2007) Standard Specification for Pressure Vessel Plates, Carbon Steel, for Intermediate- and Higher-Temperature Service
-
ASTM A516 / A516M - 03
BS EN 1759-1:2004 cites ASTM A516 / A516M - 03 Standard Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service
-
ASTM A537 / A537M - 95 (2000)
BS EN 1759-1:2004 cites ASTM A537 / A537M - 95 (2000) Standard Specification for Pressure Vessel Plates, Heat-Treated, Carbon-Manganese-Silicon Steel
-
BS EN 10025:1993
BS EN 1759-1:2004 cites BS EN 10025:1993 Hot rolled products of non-alloy structural steels. Technical delivery conditions
-
BS EN 10028-2:2003
BS EN 1759-1:2004 cites BS EN 10028-2:2003 Flat Products Made Of Steels For Pressure Purposes - Part 2: Non-alloy And Alloy Steels With Specified Elevated Temperature Properties
-
BS EN 10028-3:2003
BS EN 1759-1:2004 cites BS EN 10028-3:2003 Specification for flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized
-
BS EN 10028-4:2003
BS EN 1759-1:2004 cites BS EN 10028-4:2003 Flat products made of steels for pressure purposes - Part 4: Nickel alloy steels with specified low temperature properties
-
BS EN 10028-7:2000
BS EN 1759-1:2004 cites BS EN 10028-7:2000 Flat products made of steels for pressure purposes - Part 7: Stainless steels
-
BS EN 10213-2:1996
BS EN 1759-1:2004 cites BS EN 10213-2:1996 Technical Delivery Conditions For Steel Castings For Pressure Purposes - Part 2: Steel Grades For Use At Room Temperature And Elevated Temperatures
-
BS EN 10213-3:1996
BS EN 1759-1:2004 cites BS EN 10213-3:1996 Technical delivery conditions for steel castings for pressure purposes - Part 3: Steels for use at low temperatures
-
BS EN 10213-4:1996
BS EN 1759-1:2004 cites BS EN 10213-4:1996 Technical delivery conditions for steel castings for pressure purposes - Part 4: Austenitic and austenitic-ferritic steel grades
-
BS EN 10222-2:2000
BS EN 1759-1:2004 cites BS EN 10222-2:2000 Steel forgings for pressure purposes - Part 2: Ferritic and martensitic steels with specified elevated temperature properties
-
BS EN 10222-3:1999
BS EN 1759-1:2004 cites BS EN 10222-3:1999 Steel forgings for pressure purposes - Part 3: Nickel steels with specified low-temperature properties
-
BS EN 10222-4:1999
BS EN 1759-1:2004 cites BS EN 10222-4:1999 Steel forgings for pressure purposes - Part 4: Weldable fine-grain steels with high proof strength
-
BS EN 10222-5:2000
BS EN 1759-1:2004 cites BS EN 10222-5:2000 Steel Forgings For Pressure Purposes - Part 5: Martensitic, Austenitic and Austenitic-ferritic Stainless Steels ( EN 10222-5:1999 )
-
BS EN 1515-1:2000
BS EN 1759-1:2004 cites BS EN 1515-1:2000 Flanges and their joints - Bolting - Part 1: Selection of bolting
-
BS EN 1515-3:2005
BS EN 1759-1:2004 cites BS EN 1515-3:2005 Flanges and their joints. Bolting. Classification of bolt materials for steel flanges, class designated
-
BS EN ISO 6708:1996
BS EN 1759-1:2004 cites BS EN ISO 6708:1996 Pipework components. Definition and selection of DN (nominal size)
-
ISO 4955:1994
BS EN 1759-1:2004 cites ISO 4955:1994 Heat-resisting steels and alloys
-
ISO 4991:1994
BS EN 1759-1:2004 cites ISO 4991:1994 Steel castings for pressure purposes
-
ISO 887:2000
BS EN 1759-1:2004 cites ISO 887:2000 Plain washers for metric bolts, screws and nuts for general purposes - General plan
-
ISO 9327-1:1999
BS EN 1759-1:2004 cites ISO 9327-1:1999 Steel forgings and rolled or forged bars for pressure purposes - Technical delivery conditions - Part 1: General requirements
-
ISO 9327-2:1999
BS EN 1759-1:2004 cites ISO 9327-2:1999 Steel forgings and rolled or forged bars for pressure purposes - Technical delivery conditions - Part 2: Non-alloy and alloy (Mo, Cr and CrMo) steels with specified elevated temperature properties
-
ISO 9328-2:2004
BS EN 1759-1:2004 cites ISO 9328-2:2004 Steel flat products for pressure purposes - Technical delivery conditions - Part 2: Non-alloy and alloy steels with specified elevated temperature properties
-
ISO 9328-3:2004
BS EN 1759-1:2004 cites ISO 9328-3:2004 Steel flat products for pressure purposes - Technical delivery conditions - Part 3: Weldable fine grain steels, normalized
-
ISO 9328-5:2004
BS EN 1759-1:2004 cites ISO 9328-5:2004 Steel flat products for pressure purposes - Technical delivery conditions - Part 5: Weldable fine grain steels, thermomechanically rolled