AS/NZS 2537.3:2011 Mechanical jointing fittings for use with crosslinked polyethylene (PE-X) for pressure applications - Part 3: Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Fitness for purpose...
- Information provider
- Standards New Zealand,
- Author
- Standards New Zealand, Standards Australia
- Information type
- New Zealand Standard,
- Format
- PDF, HARD COPY,
Description
This Standard adopts ISO 15875-5:2003 with national modifications to specify the general requirements to demonstrate fitness for purpose of mechanical jointing fittings made for use with crosslinked polyethylene pipes in hot and cold water applications.
Scope
This Part of EN ISO 15875 specifies the characteristics of the fitness for purpose of crosslinked polyethylene (PE-X) piping systems, intended to be used for hot and cold water installations within buildings for the conveyance of water whether or not intended for human consumption (domestic systems) and for heating systems, under design pressures and temperatures according to the class of application (see Table 1 of EN ISO 15875-1:2003).
This standard covers a range of service conditions (application classes) and design pressure classes. For values of TD, Tmax and Tmal in excess of those in Table 1 of Part 1, this standard does not apply.
Note: It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. It also specifies the test parameters for the test methods referred to in this standard.
In conjunction with the other parts of EN ISO 15875:2003 (see Foreword) it is applicable to PE-X pipes, fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for hot and cold water installations
This resource is cited by:
AS/NZS 2537.3:2011 Mechanical jointing fittings for use with crosslinked polyethylene (PE-X) for pressure applications - Part 3: Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Fitness for purpose...
This document is CITED BY:
-
G12/AS1 (Amd 13) (Third Edition, Amendment 13)
AS/NZS 2537.3:2011 is cited by Acceptable Solution G12/AS1: Water Supplies from 2/11/2023
-
AS/NZS 3500.1:2015
AS/NZS 2537.3:2011 is cited by AS/NZS 3500.1:2015 Plumbing and drainage - Part 1: Water services
-
AS/NZS 3500.1:2018
AS/NZS 2537.3:2011 is cited by AS/NZS 3500.1:2018 Plumbing and drainage Part 1: Water services
-
AS/NZS 3500.4:2015
AS/NZS 2537.3:2011 is cited by AS/NZS 3500.4:2015 Plumbing and drainage - Heated water services
-
AS/NZS 3500.4:2018
AS/NZS 2537.3:2011 is cited by AS/NZS 3500.4:2018 Plumbing and drainage Part 4: Heated water services
-
AS/NZS 4020:2018
AS/NZS 2537.3:2011 is cited by AS/NZS 4020:2018 Testing of products for use in contact with drinking water
This resource cites:
AS/NZS 2537.3:2011 Mechanical jointing fittings for use with crosslinked polyethylene (PE-X) for pressure applications - Part 3: Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Fitness for purpose...
This document CITES:
AS/NZS 2537.3:2011 cites BS EN 12293:2000 Plastics piping systems. Thermoplastics pipes and fittings for hot and cold water. Test method for the resistance of mounted assemblies to temperature cycling
AS/NZS 2537.3:2011 cites BS EN 12294:2000 Plastic piping systems. Systems for hot and cold water. Test method for leaktightness under vacuum
AS/NZS 2537.3:2011 cites BS EN 12295:2000 Plastics piping systems. Thermoplastics pipes and associated fittings for hot and cold water. Test method for resistance of joints to pressure cycling
AS/NZS 2537.3:2011 cites BS EN 712:1995 Thermoplastics piping systems. End-load bearing mechanical joints between pressure pipes and fittings. Test method for resistance to pull-out under constant longitudinal force
AS/NZS 2537.3:2011 cites BS EN 713:1995 This Standard specifies a method for checking the leaktightness under internal hydrostatic pressure of assembled mechanical joints between fittings and polyolefin pressure pipes while subjected to bending.
AS/NZS 2537.3:2011 cites BS EN 921:1995 Plastics piping systems. Thermoplastics pipes. Determination of resistance to internal pressure at constant temperature
AS/NZS 2537.3:2011 cites ISO 15875-1:2003 Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 1: General
AS/NZS 2537.3:2011 cites ISO 15875-2:2003 Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 2: Pipes