IBS FIBRE® CTU, IBS FIBRE® Groove and IBS FIBRE® WAB

Abbreviation
CMNZ70190 version: 0
Version
0
Valid from
24/03/2026

Information provider
Ministry of Business, Innovation and Employment,
Author
Bureau Veritas Australia Pty Ltd
Information type
Product Certificate (CodeMark),
Format
PDF,

Description

IBS FIBRE® CTU is a base for laying ceramic tiles over a timber floor or reconstituted wood-based substrates and as an internal wall lining.

IBS FIBRE® WAB is an internal wall and ceiling lining in wet and dry areas and may also be used as a substrate for ceramic tiles.

For floors, it is designed for installation over timber or reconstituted wood-based substrates; wall applications do not require a timber substrate.
IBS FIBRE® Groove is an internal wall and ceiling lining in dry areas and areas subject to occasional splashes.

IBS FIBRE® CTU is a 6mm thick autoclaved cellulose fibre-reinforced cement sheet available in the following sizes: 900mm (w) or 1200mm (w) and 1800mm (l).

IBS FIBRE® WAB is a 9mm thick autoclaved cellulose fibre-reinforced cement sheet available in the following sizes: 1200 mm (w) x 2400 mm or 2700 mm (l).

IBS FIBRE® Groove is an autoclaved cellulose fibre-reinforced cement sheet 7.5mm thick with a 2.5mm deep, 5 mm wide V-shaped groove at 100 mm centres along the sheet length. Sheets are 1200 mm (w) x 2400mm or 2700mm (l).

Scope

1. IBS FIBRE® CTU, IBS FIBRE® Groove and IBS FIBRE® WAB, have been certified for the uses set out above, subject with the design and installation guides (refer to Condition 2. below) and subject to the following conditions:

  • a. In applications where a Material Group Number is required (clause C3.4(a)), IBS FIBRE® CTU, IBS FIBRE® Groove and IBS FIBRE® WAB shall be at least 9mm thick and;
  • b. In wet areas IBS FIBRE® WAB shall be at least 9mm thick and coated with water resistant paint or tiles and;
  • c. In areas adjacent to food preparation IBS FIBRE® WAB shall be at least 9mm thick and coated with water resistant paint or tiles. and
  • d. IBS FIBRE® Groove is excluded from use in areas adjacent to food preparation

2. IBS FIBRE® CTU, IBS FIBRE® Groove and IBS FIBRE® WAB shall be installed in accordance with the installation instructions for the uses in Condition 1 in the following documents:

  • IBS FIBRE® CTU - Design and Installation Guide - December 2025.
  • IBS FIBRE® Groove - Design and Installation Guide - December 2025.
  • IBS FIBRE® WAB - Design and Installation Guide - December 2025.
For assistance with locating previous versions, please contact the information provider.
View on Information Provider website
For assistance with locating previous versions, please contact the information provider.
This resource is not cited by any other resources.

IBS FIBRE® CTU, IBS FIBRE® Groove and IBS FIBRE® WAB

This document is not CITED BY any other resources:

IBS FIBRE® CTU, IBS FIBRE® Groove and IBS FIBRE® WAB

Description

IBS FIBRE® CTU is a base for laying ceramic tiles over a timber floor or reconstituted wood-based substrates and as an internal wall lining.

IBS FIBRE® WAB is an internal wall and ceiling lining in wet and dry areas and may also be used as a substrate for ceramic tiles.

For floors, it is designed for installation over timber or reconstituted wood-based substrates; wall applications do not require a timber substrate.
IBS FIBRE® Groove is an internal wall and ceiling lining in dry areas and areas subject to occasional splashes.

IBS FIBRE® CTU is a 6mm thick autoclaved cellulose fibre-reinforced cement sheet available in the following sizes: 900mm (w) or 1200mm (w) and 1800mm (l).

IBS FIBRE® WAB is a 9mm thick autoclaved cellulose fibre-reinforced cement sheet available in the following sizes: 1200 mm (w) x 2400 mm or 2700 mm (l).

IBS FIBRE® Groove is an autoclaved cellulose fibre-reinforced cement sheet 7.5mm thick with a 2.5mm deep, 5 mm wide V-shaped groove at 100 mm centres along the sheet length. Sheets are 1200 mm (w) x 2400mm or 2700mm (l).

View on Information Provider website
IBS FIBRE® CTU, IBS FIBRE® Groove and IBS FIBRE® WAB
Description

IBS FIBRE® CTU is a base for laying ceramic tiles over a timber floor or reconstituted wood-based substrates and as an internal wall lining.

IBS FIBRE® WAB is an internal wall and ceiling lining in wet and dry areas and may also be used as a substrate for ceramic tiles.

For floors, it is designed for installation over timber or reconstituted wood-based substrates; wall applications do not require a timber substrate.
IBS FIBRE® Groove is an internal wall and ceiling lining in dry areas and areas subject to occasional splashes.

IBS FIBRE® CTU is a 6mm thick autoclaved cellulose fibre-reinforced cement sheet available in the following sizes: 900mm (w) or 1200mm (w) and 1800mm (l).

IBS FIBRE® WAB is a 9mm thick autoclaved cellulose fibre-reinforced cement sheet available in the following sizes: 1200 mm (w) x 2400 mm or 2700 mm (l).

IBS FIBRE® Groove is an autoclaved cellulose fibre-reinforced cement sheet 7.5mm thick with a 2.5mm deep, 5 mm wide V-shaped groove at 100 mm centres along the sheet length. Sheets are 1200 mm (w) x 2400mm or 2700mm (l).

View on Information Provider website
This resource does not cite any other resources.

IBS FIBRE® CTU, IBS FIBRE® Groove and IBS FIBRE® WAB

This resource does not CITE any other resources.
Feedback