Description

The system is designed to be used as part of an external cladding system on timber framed building.

Stria™ Cladding is a cavity-based fibre cement panel wall cladding system. Stria™ Cladding consists of Stria™ Cladding Panel, which is a 14mm profile fibre cement panel, fixed horizontally or vertically over battens to form a nominal 20 mm cavity. Proprietary ventilated timber battens are used in vertical applications. The cladding is finished with a latex paint system.

Scope

1. The system is certified as a cavity fixed external wall cladding in:

• a. Buildings
  • i. of importance Levels 1 to 4, and
  • ii. within the scope of C/AS1, Subsection 1.1.1, or C/AS2, Subsection 1.1.1, and
  • iii. located in all exposure zones (except microclimates) as defined in NZS 3604:2011 section 4.2, and
  • iv. located anywhere in relation to the relevant boundary, and;
• b. Timber-framed buildings:
  • i. within the scope limitations of the NZBC Acceptable Solution E2/AS1, Paragraph 1.1.1, and
  • ii. with a risk score of up to 20, calculated in accordance with the NZBC Acceptable Solution E2/AS1, Table 3.1.3.1, and
  • iii. situated in in NZS 3604:2011 Wind Zones up to, and including Extra High, or
• c. Timber-framed buildings specifically engineering designed (SED):
  • i. up to 25m in height, and
  • ii. with an inter-storey drift of span/180 maximum, and
  • iii. the design ultimate limit state (ULS)differential wind pressure does not exceed 3.2 kPa, and
  • iv. with the stud and batten spacing no more than 600mm centres, and

2. The system shall be specified, installed, inspected and maintained in accordance with the following sets of documents to the extent that their scope covers that for is applicable to this Certificate:

• a. For the Horizontal applications with timber batten:
  • i. StriaTM Cladding Timber Cavity Batten Technical Specification (October 2025), and
  • ii. James Hardie Fire & Acoustic Design Manual (May 2025) section 4:17 Control of External Fire Spread, figures No’s. 2 to 11, 14 to 18 and 21 to 26, specifically details JHETGS30h and JHETGS60h.
• b. For the Vertical Application:
  • i. StriaTM Cladding Vertical Installation Technical Specification (October 2025), or StriaTM Cladding Vertical Installation to HardyTM 40mm Structural Horizontal Cavity Batten Technical Specification (October 2025), and
  • ii. James Hardie Fire & Acoustic Design Manual (May 2025) section 4:17 Control of External Fire Spread, figures No’s. 2 to 11, 14 to 18 and 21 to 26, specifically details JHETGS30v, JHETGS60v and JHETSS60v.
• c. James Hardie Fire & Acoustic Design Manual (May 2025) section 4:17 “Control of External Fire Spread”, Figure No’s 2 to 11, 14 to 18 and 21 to 26, in particular the installation details JHETGS30h, JHETGS30v, JHETGS60h and JHETGS60v. These details have only been assessed and certified with respect to external fire spread via StriaTM Cladding. For walls located within 1.0 m of a relevant boundary, StriaTM Cladding may be used as an external façade/cladding attached to the exterior of fire rated wall systems as depicted within the Fire and Acoustic Design Manual (May 2025). Fire Resistance rating performance of the wall assembly falls outside the scope of this certificate.

3. In wind zones greater than Very High a rigid air barrier which complies with Table C.2.1.1 of E2/AS1 shall be used. In buildings exceeding 10 m in height RABTM Board must be used including horizontal control joints in accordance with the requirements of the Codemark certificate (CMNZ30130) for RABTM Board.

4. The system must be used:

• a. with the ancillary components as described in this certificate, and
• b. with aluminium window and door joinery that is installed with vertical jambs and horizontal heads and sills which complies with the requirements of NZS 4211:2008 including amendment 1 for the relevant Wind Zone or wind pressure or have a current CodeMark.

5. StriaTM Cladding shall only be installed on vertical surfaces.

6. All exposed faces, including top edges at sills and all bottom edges of StriaTM Cladding panel and fibre cement ancillary components shall be finished with a latex exterior paint system complying with any of Parts 7, 8, 9, or 10 of AS 3730.

7. E2.3.5 and E2.3.6 compliance is limited to cavities created between the internal surface of the panels and the underlay or RABTM Boards.