BS EN 1254-3:1998 Copper And Copper Alloys - Plumbing Fittings - Part 3: Fittings With Compression Ends For Use With Plastic Pipes

Abbreviation
BS EN 1254-3:1998
Valid from
15/06/1998

Information provider
British Standards Institution,
Author
British Standards Institution, European Standardization Organisation
Information type
European Standard,
Format
PDF, HARD COPY,


Description

This Standard specifies product characteristics, assessment methods, compliance criteria of test results and a designation system for fittings with compression ends for use with plastics and multilayer pipes which are defined in the applicable pipe standard. For the purposes of joining plastics pipes, the fitting ends have a nominal diameter from 6mm to 160mm. The fittings are designed for a service lifetime up to fifty years.

The compression fittings are used up to the operating temperatures and corresponding maximum operating pressures as indicated in AnnexA.

Scope

This Standard applies to copper alloy fittings. A non-exhaustive list of these copper alloys is given in CEN/TS 13388.

Adaptor fittings for use with plastics and multilayer pipes may combine compression ends with fitting ends defined in the other parts of EN1254.

Compression fittings for use with plastics and multilayer pipes may also have a plated or other decorative surface coating.

Fittings can be produced by machining, metal forming, casting, or fabrication.

Products covered by this standard are intended to be used in:

1. liquid applications:

  • hot, cold or combined hot and cold water, including systems according to EN806;
  • closed heating systems according to EN12828;
  • cooling systems;
  • drainage systems;
  • fire protection systems including sprinkler systems according to EN12845.

2. gas applications (not valid for multilayer pipes):

  • natural gas and liquefied petroleum gas systems with a maximum operating pressure less than or equal to 5 bar according to EN1775 ;
  • compressed air systems.
    For assistance with locating previous versions, please contact the information provider.
    View on Information Provider website
    For assistance with locating previous versions, please contact the information provider.
    This resource is cited by:

    BS EN 1254-3:1998 Copper And Copper Alloys - Plumbing Fittings - Part 3: Fittings With Compression Ends For Use With Plastic Pipes

    This document is CITED BY:

    BS EN 1254-3:1998 Copper And Copper Alloys - Plumbing Fittings - Part 3: Fittings With Compression Ends For Use With Plastic Pipes

    Description

    This Standard specifies product characteristics, assessment methods, compliance criteria of test results and a designation system for fittings with compression ends for use with plastics and multilayer pipes which are defined in the applicable pipe standard. For the purposes of joining plastics pipes, the fitting ends have a nominal diameter from 6mm to 160mm. The fittings are designed for a service lifetime up to fifty years.

    The compression fittings are used up to the operating temperatures and corresponding maximum operating pressures as indicated in AnnexA.

    View on Information Provider website
    BS EN 1254-3:1998 Copper And Copper Alloys - Plumbing Fittings - Part 3: Fittings With Compression Ends For Use With Plastic Pipes
    Description

    This Standard specifies product characteristics, assessment methods, compliance criteria of test results and a designation system for fittings with compression ends for use with plastics and multilayer pipes which are defined in the applicable pipe standard. For the purposes of joining plastics pipes, the fitting ends have a nominal diameter from 6mm to 160mm. The fittings are designed for a service lifetime up to fifty years.

    The compression fittings are used up to the operating temperatures and corresponding maximum operating pressures as indicated in AnnexA.

    View on Information Provider website
    This resource does not cite any other resources.

    BS EN 1254-3:1998 Copper And Copper Alloys - Plumbing Fittings - Part 3: Fittings With Compression Ends For Use With Plastic Pipes

    This resource does not CITE any other resources.
    Feedback