AS/NZS 7671:2010 Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings - Polypropylene (PP)
- Abbreviation
- AS/NZS 7671:2010
- Amendment
- A1, A2 - incorporated.
- Valid from
- 18/08/2010
- Information provider
- Standards New Zealand,
- Author
- Standards New Zealand, Standards Australia
- Information type
- New Zealand Standard,
- Format
- PDF, HARD COPY,
Description
This Standard specifies the requirements for solid-wall polypropylene (PP) pipes and fittings for soil and waste discharge inside buildings, as well as the system itself.
Adopted with national modifications from ISO 7671:2003. These minor variations to the ISO Standard relate to normative references (some EN test methods have been replaced by current ISO or AS/NZS Standards) and marking requirements and do not change its technical content. These modifications and variations are listed in Appendix ZZ.
Scope
This Standard does not include buried pipework. It also specifies the test parameters for the test methods referred to in this International Standard.
This International Standard is applicable to PP pipes and fittings, as well as assemblies of such pipes and fittings, intended to be used for the following purposes:
- a) soil and waste discharge pipework for the conveyance of domestic waste waters (low and high temperature);
- b) ventilation pipework associated with a);
- c) rainwater pipework inside the building.
It is applicable to pipes and fittings for jointing by means of elastomeric sealing rings or by butt fusion.
This resource is cited by:
AS/NZS 7671:2010 Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings - Polypropylene (PP)
This document is CITED BY:
-
G13/AS1 (Amd 10) (Second Edition, Amendment 10)
AS/NZS 7671:2010 is cited by Acceptable Solution G13/AS1: Sanitary Plumbing from 2/11/2023
-
AS/NZS 3500.2:2015
AS/NZS 7671:2010 is cited by AS/NZS 3500.2:2015 Plumbing and drainage - Part 2: Sanitary plumbing and drainage
-
AS/NZS 3500.2:2018
AS/NZS 7671:2010 is cited by AS/NZS 3500.2:2018 Plumbing and drainage Part 2: Sanitary plumbing and drainage
This resource cites:
AS/NZS 7671:2010 Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings - Polypropylene (PP)
This document CITES:
AS/NZS 7671:2010 cites BS EN 1053:1996 Plastics piping systems - Thermoplastics piping systems for non-pressure applications - Test methods for watertightness
AS/NZS 7671:2010 cites BS EN 1054:1996 Plastics piping systems. Thermoplastics piping systems for soil and waste discharge. Test method for airtightness of joints
AS/NZS 7671:2010 cites BS EN 1055:1996 Plastics piping systems. Thermoplastics piping systems for soil and waste discharge inside buildings. Test method for resistance to elevated temperature cycling
AS/NZS 7671:2010 cites BS EN 1411:1996 Plastics piping and ducting systems. Thermoplastics pipes. Determination of resistance to external blows by the staircase method
AS/NZS 7671:2010 cites BS EN 681-1:1996 Elastomeric seals. Material requirements for pipe joint seals used in water and drainage applications - Part 1: Vulcanized rubber
AS/NZS 7671:2010 cites BS EN 681-2:2000 Elastomeric Seals - Materials Requirements For Pipe Joint Seals Used In Water And Drainage Applications - Part 2: Thermoplastic Elastomers
AS/NZS 7671:2010 cites BS EN 728:1997 Plastics piping and ducting systems. Polyolefin pipes and fittings. Determination of oxidation induction time
AS/NZS 7671:2010 cites BS EN 743:1995 Plastics piping and ducting systems. Thermoplastics pipes. Determination of the longitudinal reversion
AS/NZS 7671:2010 cites BS EN 744:1996 Plastics piping and ducting systems. Thermoplastics pipes. Test method for resistance to external blows by the round-the-clock method
AS/NZS 7671:2010 cites BS EN 763:1995 Plastics piping and ducting systems. Injection-moulded thermoplastics fittings. Test method for visually assessing effects of heating
AS/NZS 7671:2010 cites ISO 1133:1997 Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
AS/NZS 7671:2010 cites ISO 265-1:1988 Pipes and fittings of plastics materials - Fittings for domestic and industrial waste pipes - Basic dimensions: Metric series Part 1: Unplasticized poly(vinyl chloride) (PVC-U)
AS/NZS 7671:2010 cites ISO 3126:2005 Plastics piping systems - Plastics components - Determination of dimensions