ISO 1268-4:2005 Fibre-reinforced plastics - Methods of producing test plates - Part 4: Moulding of prepregs

Abbreviation
ISO 1268-4:2005
Amendment
ISO 1268-4:2005/Amd 1:2010
Valid from
23/03/2005

Information provider
Standards New Zealand,
Author
International Organization for Standardization
Information type
ISO Standard,
Format
PDF, HARD COPY,


Description

This part of ISO 1268 describes the preparation of test plates from layers of pre-impregnated unidirectional fibre or fabric (prepregs) under pressure and temperature in various types of equipment (for example, autoclave, bladder press, hydraulic press or vacuum bag equipment). It applies to all reinforcements and resins.

This method is applicable to reinforcements pre-impregnated either with a partially cured thermosetting resin or with a thermoplastic resin. The test plate is formed by stacking layers of the pre-impregnated material in the required sequence and orientation, followed by compaction and final consolidation under pressure/vacuum at a temperature above ambient. The prepared test plates are subsequently machined into the required test specimens.

Standard plates prepared in this manner may be used either for evaluating the components, i.e. the reinforcement, finish, resin, etc., or for verifying the overall quality of the finished product.

For assistance with locating previous versions, please contact the information provider.
Notes/comments

This Standard is referenced by AS/NZS 1546.1:2008 in regard to septic tanks.

View on Information Provider website
For assistance with locating previous versions, please contact the information provider.

This Standard is referenced by AS/NZS 1546.1:2008 in regard to septic tanks.

This resource is cited by:

ISO 1268-4:2005 Fibre-reinforced plastics - Methods of producing test plates - Part 4: Moulding of prepregs

This document is CITED BY:

ISO 1268-4:2005 Fibre-reinforced plastics - Methods of producing test plates - Part 4: Moulding of prepregs

Description

This part of ISO 1268 describes the preparation of test plates from layers of pre-impregnated unidirectional fibre or fabric (prepregs) under pressure and temperature in various types of equipment (for example, autoclave, bladder press, hydraulic press or vacuum bag equipment). It applies to all reinforcements and resins.

This method is applicable to reinforcements pre-impregnated either with a partially cured thermosetting resin or with a thermoplastic resin. The test plate is formed by stacking layers of the pre-impregnated material in the required sequence and orientation, followed by compaction and final consolidation under pressure/vacuum at a temperature above ambient. The prepared test plates are subsequently machined into the required test specimens.

Standard plates prepared in this manner may be used either for evaluating the components, i.e. the reinforcement, finish, resin, etc., or for verifying the overall quality of the finished product.

View on Information Provider website
ISO 1268-4:2005 Fibre-reinforced plastics - Methods of producing test plates - Part 4: Moulding of prepregs
Description

This part of ISO 1268 describes the preparation of test plates from layers of pre-impregnated unidirectional fibre or fabric (prepregs) under pressure and temperature in various types of equipment (for example, autoclave, bladder press, hydraulic press or vacuum bag equipment). It applies to all reinforcements and resins.

This method is applicable to reinforcements pre-impregnated either with a partially cured thermosetting resin or with a thermoplastic resin. The test plate is formed by stacking layers of the pre-impregnated material in the required sequence and orientation, followed by compaction and final consolidation under pressure/vacuum at a temperature above ambient. The prepared test plates are subsequently machined into the required test specimens.

Standard plates prepared in this manner may be used either for evaluating the components, i.e. the reinforcement, finish, resin, etc., or for verifying the overall quality of the finished product.

View on Information Provider website
This resource does not cite any other resources.

ISO 1268-4:2005 Fibre-reinforced plastics - Methods of producing test plates - Part 4: Moulding of prepregs

This resource does not CITE any other resources.
Feedback