StoLite Stucco Cladding System

Abbreviation
Appraisal number 468 (2024)
Valid from
3/07/2024

Information provider
BRANZ Limited,
Information type
BRANZ Appraisal,
Format
PDF,

Description

StoLite is a cavity-based monolithic stucco render wall cladding.  It is designed to be used as an external wall cladding system for residential and light commercial type buildings where domestic construction techniques are used. 

The system consists of minimum 6 mm thick fibre cement sheets fixed over timber battens to  form the cavity. The coating system consists of a nominal 8 mm thick polystyrene bead-saturated,  polymer-modified, cement-based render applied to the fibre cement sheets, an approximate  2.5 mm thick coat of meshed reinforcement render, and an approximate 1-3 mm thick coat of  coloured finishing render. The render system is finished with a Sto coating.

Scope

1. StoLite has been appraised as an external wall cladding system for buildings within the following scope:

  • the scope limitations of NZBC Acceptable Solution E2/AS1, Paragraph 1.1; and,
  • with a risk score of 0-20, calculated in accordance with NZBC Acceptable Solution E2/AS1, Table 2; and,
  • situated in NZS 3604 Wind Zones up to, and including Extra High.

2. StoLite has also been appraised for weathertightness and structural wind loading when used as an external wall cladding system for buildings within the following scope:

  • the scope limitations of NZBC Acceptable Solution E2/AS1, Paragraph 1.1 with regards to building height and floor plan area; and,
  • constructed with timber framing subject to specific engineering design; and,
  • situated in specific design wind pressures up to a maximum design differential ultimate limit state (ULS) of 2.5 kPa.

3. StoLite must only be installed on vertical surfaces (except for tops of parapets, sills and balustrades, which must have a minimum 10º slope and be waterproofed in accordance with the Technical Literature).

4. The system is appraised for use with aluminium window and door joinery that is installed with vertical jambs and horizontal heads and sills. (The Appraisal of the StoLite Stucco Cladding System relies on the joinery meeting the requirements of NZS 4211 for the relevant Wind Zone, or wind pressure.)

5. Installation of components and accessories supplied by Stoanz Limited and Sto registered contractors must be carried out only by Sto registered contractors.

For assistance with locating previous versions, please contact the information provider.
Notes/comments

This Appraisal replaces BRANZ Appraisal No 468 (2018).

View on Information Provider website Download this resource (PDF, 883KB)
For assistance with locating previous versions, please contact the information provider.

This Appraisal replaces BRANZ Appraisal No 468 (2018).

This resource is not cited by any other resources.

StoLite Stucco Cladding System

This document is not CITED BY any other resources:

StoLite Stucco Cladding System

Description

StoLite is a cavity-based monolithic stucco render wall cladding.  It is designed to be used as an external wall cladding system for residential and light commercial type buildings where domestic construction techniques are used. 

The system consists of minimum 6 mm thick fibre cement sheets fixed over timber battens to  form the cavity. The coating system consists of a nominal 8 mm thick polystyrene bead-saturated,  polymer-modified, cement-based render applied to the fibre cement sheets, an approximate  2.5 mm thick coat of meshed reinforcement render, and an approximate 1-3 mm thick coat of  coloured finishing render. The render system is finished with a Sto coating.

View on Information Provider website Download this resource (PDF, 883KB)
StoLite Stucco Cladding System
Description

StoLite is a cavity-based monolithic stucco render wall cladding.  It is designed to be used as an external wall cladding system for residential and light commercial type buildings where domestic construction techniques are used. 

The system consists of minimum 6 mm thick fibre cement sheets fixed over timber battens to  form the cavity. The coating system consists of a nominal 8 mm thick polystyrene bead-saturated,  polymer-modified, cement-based render applied to the fibre cement sheets, an approximate  2.5 mm thick coat of meshed reinforcement render, and an approximate 1-3 mm thick coat of  coloured finishing render. The render system is finished with a Sto coating.

View on Information Provider website Download this resource (PDF, 883KB)
This resource does not cite any other resources.

StoLite Stucco Cladding System

This resource does not CITE any other resources.
Feedback