ISO 8533:2003 Plastics piping systems for pressure and non-pressure drainage and sewerage — Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin — Test methods to prove the design of cemented or wrapped joints

Abbreviation
ISO 8533:2003
Valid from
1/12/2003

Information provider
Standards New Zealand
Author
International Organization for Standardization
Information type
ISO Standard
Format
PDF


Description

ISO 8533:2003 specifies methods of test for cemented or wrapped joints for plastics piping systems made of glass-reinforced thermosetting plastics (GRP) for buried and non-buried pipelines. This standard is only applicable to the joint and covers methods of test to prove its design. It assumes that the joint either is or is not intended to be subject to the effects of hydrostatic end thrust.

The tests are applicable to cemented or wrapped joints intended to be used in either buried or non-buried applications. The bending tests can be used to prove the design where joints are either intended to be used in buried applications or are intended to be used in particular above-ground situations where the tests may be considered appropriate.

With the exception of the bending tests, these test procedures are applicable to joints between pipes and fittings of all nominal sizes. The bending tests are applicable to joints between pipes and fittings up to and including DN 600. The tests are applicable to the evaluation of joints intended for the conveyance of liquids at temperatures specified in the referring standards.

For assistance with locating previous versions, please contact the information provider.
View on Information Provider website
For assistance with locating previous versions, please contact the information provider.
This resource is cited by:

ISO 8533:2003 Plastics piping systems for pressure and non-pressure drainage and sewerage — Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin — Test methods to prove the design of cemented or wrapped joints

This document is CITED BY:

ISO 8533:2003 Plastics piping systems for pressure and non-pressure drainage and sewerage — Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin — Test methods to prove the design of cemented or wrapped joints

Description

ISO 8533:2003 specifies methods of test for cemented or wrapped joints for plastics piping systems made of glass-reinforced thermosetting plastics (GRP) for buried and non-buried pipelines. This standard is only applicable to the joint and covers methods of test to prove its design. It assumes that the joint either is or is not intended to be subject to the effects of hydrostatic end thrust.

The tests are applicable to cemented or wrapped joints intended to be used in either buried or non-buried applications. The bending tests can be used to prove the design where joints are either intended to be used in buried applications or are intended to be used in particular above-ground situations where the tests may be considered appropriate.

With the exception of the bending tests, these test procedures are applicable to joints between pipes and fittings of all nominal sizes. The bending tests are applicable to joints between pipes and fittings up to and including DN 600. The tests are applicable to the evaluation of joints intended for the conveyance of liquids at temperatures specified in the referring standards.

View on Information Provider website
ISO 8533:2003 Plastics piping systems for pressure and non-pressure drainage and sewerage — Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin — Test methods to prove the design of cemented or wrapped joints
Description

ISO 8533:2003 specifies methods of test for cemented or wrapped joints for plastics piping systems made of glass-reinforced thermosetting plastics (GRP) for buried and non-buried pipelines. This standard is only applicable to the joint and covers methods of test to prove its design. It assumes that the joint either is or is not intended to be subject to the effects of hydrostatic end thrust.

The tests are applicable to cemented or wrapped joints intended to be used in either buried or non-buried applications. The bending tests can be used to prove the design where joints are either intended to be used in buried applications or are intended to be used in particular above-ground situations where the tests may be considered appropriate.

With the exception of the bending tests, these test procedures are applicable to joints between pipes and fittings of all nominal sizes. The bending tests are applicable to joints between pipes and fittings up to and including DN 600. The tests are applicable to the evaluation of joints intended for the conveyance of liquids at temperatures specified in the referring standards.

View on Information Provider website
This resource does not cite any other resources.

ISO 8533:2003 Plastics piping systems for pressure and non-pressure drainage and sewerage — Glass-reinforced thermosetting plastics (GRP) systems based on unsaturated polyester (UP) resin — Test methods to prove the design of cemented or wrapped joints

This resource does not CITE any other resources.
Feedback