AS/NZS 1260:2009 PVC-U Pipes and fittings for drain, waste and vent applications
- Abbreviation
- AS/NZS 1260:2009
- Amendment
- AS/NZS 1260:2009 A1 . - incorporated. Published 11/04/2011, AS/NZS 1260:2009 A2 . - incorporated. Published 17/12/2013.
- Valid from
- 15/06/2009
- Replaces
- AS/NZS 1260:2002
- Information provider
- Standards New Zealand
- Author
- Standards New Zealand, Standards Australia
- Information type
- New Zealand Standard
- Format
- PDF, HARD COPY
Description
This Standard specifies requirements for PVC-U pipes and fittings for sewer, drain, waste and vent applications above ground or below ground and is intended to be used where the pipeline is operating under gravity flow and the operating pressure is low.
The Standard includes requirements for both plain and structured wall pipes and fittings. Pipes manufactured to this Standard should be used and installed in accordance with AS/NZS 2032, AS/NZS 2566.1, AS/NZS 2566.2, or AS/NZS 3500.2, AS/NZS 3500.5.
This resource is cited by:
AS/NZS 1260:2009 PVC-U Pipes and fittings for drain, waste and vent applications
This document is CITED BY:
-
E1/AS1 (Amd 10) (First Edition, Amendment 10)
AS/NZS 1260:2009 is cited by Acceptable Solution E1/AS1: Surface Water from 30/09/2010 until 3/11/2021
-
E1/AS1 (Amd 9) (First Edition, Amendment 9)
AS/NZS 1260:2009 is cited by Acceptable Solution E1/AS1: Surface Water from 30/09/2010
-
E1/AS1 (Amd 8) (First Edition, Amendment 8)
AS/NZS 1260:2009 is cited by Acceptable Solution E1/AS1: Surface Water from 30/09/2010
-
G13/AS1 (Second Edition, Amendment 5)
AS/NZS 1260:2009 is cited by Acceptable Solution G13/AS1: Sanitary Plumbing from 10/10/2011
-
G13/AS1 (Second Edition, Amendment 8)
AS/NZS 1260:2009 is cited by Acceptable Solution G13/AS1: Sanitary Plumbing from 10/10/2011 until 3/11/2021
-
G13/AS1 (Second Edition, Amendment 7)
AS/NZS 1260:2009 is cited by Acceptable Solution G13/AS1: Sanitary Plumbing from 10/10/2011
-
G13/AS1 (Second Edition, Amendment 4)
AS/NZS 1260:2009 is cited by Acceptable Solution G13/AS1: Sanitary Plumbing from 10/10/2011
-
G13/AS1 (Second Edition, Amendment 6)
AS/NZS 1260:2009 is cited by Acceptable Solution G13/AS1: Sanitary Plumbing from 10/10/2011
-
G13/AS2 (Second Edition, Amendment 5)
AS/NZS 1260:2009 is cited by Acceptable Solution G13/AS2: Drainage from 10/10/2011
-
G13/AS2 (Second Edition, Amendment 4)
AS/NZS 1260:2009 is cited by Acceptable Solution G13/AS2: Drainage from 10/10/2011
-
G13/AS2 (Second Edition, Amendment 6)
AS/NZS 1260:2009 is cited by Acceptable Solution G13/AS2: Drainage from 10/10/2011
-
G13/AS2 (Second Edition, Amendment 7)
AS/NZS 1260:2009 is cited by Acceptable Solution G13/AS2: Drainage from 10/10/2011
-
G13/AS2 (Second Edition, Amendment 8)
AS/NZS 1260:2009 is cited by Acceptable Solution G13/AS2: Drainage from 10/10/2011 until 3/11/2021
-
G14/VM1 (Amd 6) (Second Edition, Amendment 6)
AS/NZS 1260:2009 is cited by Verification Method G14/VM1: Industrial Liquid Waste from 10/10/2011
-
G14/VM1 (Amd 5) (Second Edition, Amendment 5)
AS/NZS 1260:2009 is cited by Verification Method G14/VM1: Industrial Liquid Waste from 10/10/2011
-
G14/VM1 (Second Edition, Amendment 4)
AS/NZS 1260:2009 is cited by Verification Method G14/VM1: Industrial Liquid Waste from 10/10/2011
-
AS/NZS 1254:2010
AS/NZS 1260:2009 is cited by AS/NZS 1254:2010 PVC-U pipes and fittings for stormwater and surface water applications
-
AS/NZS 3500.2:2015
AS/NZS 1260:2009 is cited by AS/NZS 3500.2:2015 Plumbing and drainage - Part 2: Sanitary plumbing and drainage
-
AS/NZS 3500.4:2015
AS/NZS 1260:2009 is cited by AS/NZS 3500.4:2015 Plumbing and drainage - Heated water services
-
AS/NZS 3879:2011
AS/NZS 1260:2009 is cited by AS/NZS 3879:2011 Solvent cements and priming fluids for PVC (PVC-U and PVC-M) and ABS and ASA pipes and fittings
-
AS/NZS 5601.1:2010
AS/NZS 1260:2009 is cited by AS/NZS 5601.1:2010 Gas installations - Part 1: General installations
-
AS/NZS 5601.1:2013
AS/NZS 1260:2009 is cited by AS/NZS 5601.1:2013 Gas installations - General installations
This resource cites:
AS/NZS 1260:2009 PVC-U Pipes and fittings for drain, waste and vent applications
This document CITES:
New Zealand Standards
-
AS/NZS 1462.11:1996
AS/NZS 1260:2009 cites AS/NZS 1462.11:1996 (R2017) Methods of test for plastics pipes and fittings - Method 11: Method for high temperature stress-relief testing of fittings
-
AS/NZS 1462.13:2006
AS/NZS 1260:2009 cites AS/NZS 1462.13:2006 (R2017) Methods of test for plastics pipes and fittings - Method 13: Method for the determination of elastomeric seal joint contact width and pressure
-
AS/NZS 1462.15:1996
AS/NZS 1260:2009 cites AS/NZS 1462.15:1996 (R2017) Methods of test for plastics pipes and fittings - Method 15: Method for determination of vinyl chloride monomer content
-
AS/NZS 1462.16:2006
AS/NZS 1260:2009 cites AS/NZS 1462.16:2006 (R2017) Methods of test for plastics pipes and fittings - Method 16: Method for high temperature testing of pipe
-
AS/NZS 1462.1:2006
AS/NZS 1260:2009 cites AS/NZS 1462.1:2006 Methods of test for plastics pipes and fittings - Method 1: Method for determining the dimensions of pipes and fittings
-
AS/NZS 1462.21:1997
AS/NZS 1260:2009 cites AS/NZS 1462.21:1997 (R2017) Methods of test for plastics pipes and fittings - Method 21: Method for determination of bond strength
-
AS/NZS 1462.22:1997
AS/NZS 1260:2009 cites AS/NZS 1462.22:1997 Methods of test for plastics pipes and fittings - Method 22: Method for determination of pipe stiffness
-
AS/NZS 1462.23:2006
AS/NZS 1260:2009 cites AS/NZS 1462.23:2006 Methods of test for plastics pipes and fittings - Method 23: Method for determination of ring flexibility
-
AS/NZS 1462.2:2006
AS/NZS 1260:2009 cites AS/NZS 1462.2:2006 (R2017) Methods of test for plastics pipes and fittings - Method 2: Method for determining the flattening properties of plastics pipes and fittings
-
AS/NZS 1462.3:1998
AS/NZS 1260:2009 cites AS/NZS 1462.3:1998 (R2017) Methods of test for plastics pipes and fittings - Method 3: Method for determining the impact characteristics of pipes
-
AS/NZS 1462.4:2002
AS/NZS 1260:2009 cites AS/NZS 1462.4:2002 (R2017) Methods of test for plastics pipes and fittings - Method 4: Method of determining reversion of UPVC pipes
-
AS/NZS 1462.5:2002
AS/NZS 1260:2009 cites AS/NZS 1462.5:2002 (R2017) Methods of test for plastics pipes and fittings - Method 5: Vicat softening temperature
-
AS/NZS 1462.8:2008
AS/NZS 1260:2009 cites AS/NZS 1462.8:2008 (R2017) Methods of test for plastics pipes and fittings - Method 8: Method of testing the leaktightness of assemblies
-
AS/NZS 1477:2006
AS/NZS 1260:2009 cites AS/NZS 1477:2006 PVC pipes and fittings for pressure applications
-
AS/NZS 2032:2006
AS/NZS 1260:2009 cites AS/NZS 2032:2006 Installation of PVC pipe systems
-
AS/NZS 3500.0:2003
AS/NZS 1260:2009 cites AS/NZS 3500.0:2003 Plumbing and drainage - Glossary of terms
-
AS/NZS 3879:2006
AS/NZS 1260:2009 cites AS/NZS 3879:2006 Solvent cements and priming fluids for PVC (PVC-U and PVC-M) and ABS pipes and fittings
-
AS/NZS 4765:2007
AS/NZS 1260:2009 cites AS/NZS 4765:2007 Modified polyvinyl chloride (PVC-M) pipes for pressure applications
-
NZS 7702:1989
AS/NZS 1260:2009 cites NZS 7702:1989 Specification for colours for identification, coding and special purposes
Australian Standards
-
AS 1172.1-2005
AS/NZS 1260:2009 cites AS 1172.1-2005 Water closets (WC) - Part 1: Pans
-
AS 1199.1-2003 (R2016)
AS/NZS 1260:2009 cites AS 1199.1-2003 (R2016) Sampling procedures for inspection by attributes - Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
-
AS 1646-2007
AS/NZS 1260:2009 cites AS 1646-2007 (R2018) Elastomeric seals for waterworks purposes
-
AS 2700-1996
AS/NZS 1260:2009 cites AS 2700-1996 Colour Standards for general purposes
-
AS 2887-1993
AS/NZS 1260:2009 cites AS 2887-1993 (R2017) Plastic waste fittings
-
AS 681.1-2008
AS/NZS 1260:2009 cites AS 681.1-2008 Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 1: Vulcanized rubber
-
AS 681.2-2008
AS/NZS 1260:2009 cites AS 681.2-2008 Elastomeric seals - Material requirements for pipe joint seals used in water and drainage applications - Part 2: Thermoplastic elastomers
Other
-
BS EN 1055:1996
AS/NZS 1260:2009 cites BS EN 1055:1996 Plastics piping systems. Thermoplastics piping systems for soil and waste discharge inside buildings. Test method for resistance to elevated temperature cycling
-
HB 18.28-2005
AS/NZS 1260:2009 cites HB 18.28-2005 Conformity assessment - Guidance on a third-party certification system for products
-
ISO 13967:2009
AS/NZS 1260:2009 cites ISO 13967:2009 Thermoplastics fittings - Determination of ring stiffness
-
ISO 3951-1:2005
AS/NZS 1260:2009 cites ISO 3951-1:2005 Sampling procedures for inspection by variables - Part 1: Specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection for a single quality characteristic and a single AQL
-
ISO 3951-2:2006
AS/NZS 1260:2009 cites ISO 3951-2:2006 Sampling procedures for inspection by variables Part 2: General specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection of independent quality characteristics
-
ISO 3951-3:2007
AS/NZS 1260:2009 cites ISO 3951-3:2007 Sampling procedures for inspection by variables - Part 3: Double sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection
-
ISO 3951-5:2006
AS/NZS 1260:2009 cites ISO 3951-5:2006 Sampling procedures for inspection by variables Part 5: Sequential sampling plans indexed by acceptance quality limit (AQL) for inspection by variables (known standard deviation)
-
ISO/IEC 17050-1:2004
AS/NZS 1260:2009 cites ISO/IEC 17050-1:2004 Conformity assessment - Supplier's declaration of conformity - Part 1: General requirements
-
ISO/IEC 17050-2:2004
AS/NZS 1260:2009 cites ISO/IEC 17050-2:2004 Preview Conformity assessment -- Supplier's declaration of conformity -- Part 2: Supporting documentation