AS 1357.1-2019 Valves primarily for use in heated water systems - Part 1: Protection valves
- Abbreviation
- AS 1357.1:2019
- Valid from
- 20/12/2019
- Information provider
- Intertek Inform
- Author
- Standards Australia
- Information type
- Australian Standard
- Format
- PDF, HARD COPY
Description
The objective of this Standard is to provide manufacturers with design, materials and performance requirements for the protection of valves.
Scope
This Standard sets out requirements for the design, construction, testing and performance of the following types of valves, within the range of DN 15 to DN 50:
- a) Temperature/pressure-relief valves.
- b) Expansion-control valves.
- c) Non-return valves.
- d) Temperature-relief valves.
- e) Combination high-pressure expansion non-return valves (HPNR).
- f) Leak-protection devices.
The valves specified in this Standard are primarily intended for use in warm and hot water systems that are required to operate at —
- i) continuous operating temperatures not exceeding 85 °C;
- ii) temperatures under emergency conditions, not exceeding 99 °C; and
- iii) continuous working pressure not exceeding 1400 kPa.
NOTE: For valves used with water heaters that are intended to operate at temperatures above 99 °C (e.g. hot water boilers), see AS 1271.
This resource is cited by:
AS 1357.1-2019 Valves primarily for use in heated water systems - Part 1: Protection valves
This document is CITED BY:
-
G12/AS1 (Amd 13) (Third Edition, Amendment 13)
AS 1357.1:2019 is cited by Acceptable Solution G12/AS1: Water Supplies from 2/11/2023
-
AS 3498:2020
AS 1357.1:2019 is cited by AS 3498:2020 Safety and public health requirements for plumbing products - Water heaters and hot-water storage tanks
-
AS/NZS 5263.1.2:2020
AS 1357.1:2019 is cited by AS/NZS 5263.1.2:2020 Gas appliances - Part 1.2: Gas fired water heaters for hot water supply and/or central heating
This resource cites:
AS 1357.1-2019 Valves primarily for use in heated water systems - Part 1: Protection valves
This document CITES:
New Zealand Standards
-
AS/NZS 1167.1:2005
AS 1357.1:2019 cites AS/NZS 1167.1:2005 Welding and brazing - Filler metals - Filler metal for brazing and braze welding
-
AS/NZS 1567:1997
AS 1357.1:2019 cites AS/NZS 1567:1997 Copper and copper alloys - Wrought rods, bars and sections
-
AS/NZS 1568:1998
AS 1357.1:2019 cites AS/NZS 1568:1998 Copper and copper alloys - Forging stock and forgings
-
AS/NZS 3500.0:2003
AS 1357.1:2019 cites AS/NZS 3500.0:2003 Plumbing and drainage - Glossary of terms
-
AS/NZS 4020:2018
AS 1357.1:2019 cites AS/NZS 4020:2018 Testing of products for use in contact with drinking water
-
NZS 3501:1976
AS 1357.1:2019 cites NZS 3501:1976 Specification for copper tubes for water, gas, and sanitation - SPONSORED
Australian Standards
-
AS 1349-1986
AS 1357.1:2019 cites AS 1349-1986 (R2018) Bourdon tube pressure and vacuum gauges
-
AS 1432-2004 (R2016)
AS 1357.1:2019 cites AS 1432-2004 (R2016) Copper tubes for plumbing, gasfitting and drainage applications
-
AS 1565-1996 (Reconfirmed in 2020)
AS 1357.1:2019 cites AS 1565-1996 Copper and copper alloys - Ingots and castings
-
AS 1572-1998 (Reconfirmed in 2018)
AS 1357.1:2019 cites AS 1572-1998 (R2018) Copper and copper alloys - Seamless tubes for engineering purposes
-
AS 1722.2-1992 (Reconfirmed in 2017)
AS 1357.1:2019 cites AS 1722.2-1992 (R2017) Pipe threads of Whitworth form - Part 2: Fastening pipe threads
-
AS 1834.1-1991
AS 1357.1:2019 cites AS 1834.1-1991 (R2018) Material for soldering - Part 1: Solder alloys
-
AS 2345-2006 (R2016)
AS 1357.1:2019 cites AS 2345-2006 (R2016) Dezincification resistance of copper alloys
-
AS 2738-2000
AS 1357.1:2019 cites AS 2738-2000 (R2018) Copper and copper alloys - Compositions and designations of refinery products, wrought products, ingots and castings
-
AS 2837-1986
AS 1357.1:2019 cites AS 2837-1986 Wrought alloy steels - Stainless steel bars and semi-finished products
-
AS 3558.5-1999
AS 1357.1:2019 cites AS 3558.5-1999 (R2016) Methods of testing plastics and composite materials sanitary plumbing fixtures - Method 5: Determination of degradation by ultraviolet light
-
AS 3688:2016
AS 1357.1:2019 cites AS 3688:2016 Water supply and gas systems - Metallic fittings and end connectors
-
AS ISO 7.1-2008
AS 1357.1:2019 cites AS ISO 7.1-2008 (R2017) Pipe threads where pressure-tight joints are made on the threads - Dimensions, tolerances and designation
Other
-
ASTM A269/A269M-15a
AS 1357.1:2019 cites ASTM A269/A269M-15a Standard Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General Service
-
ASTM A276/A276M-17
AS 1357.1:2019 cites ASTM A276/A276M-17 Standard Specification for Stainless Steel Bars and Shapes
-
ASTM A313/A313M-18
AS 1357.1:2019 cites ASTM A313/A313M-18 Standard Specification for Stainless Steel Spring Wire
-
ASTM B127-05 (2014)
AS 1357.1:2019 cites ASTM B127-05 (2014) Standard Specification for Nickel-Copper Alloy (UNS N04400) Plate, Sheet, and Strip
-
ASTM B163-18
AS 1357.1:2019 cites ASTM B163-18 Standard Specification for Seamless Nickel and Nickel Alloy Condenser and Heat-Exchanger Tubes
-
ASTM B164-03(2019) (Reconfirmed in 2019)
AS 1357.1:2019 cites ASTM B164-03(2019) Standard Specification for Nickel-Copper Alloy Rod, Bar, and Wire
-
ASTM B165-19
AS 1357.1:2019 cites ASTM B165-19 Standard Specification for Nickel-Copper Alloy Seamless Pipe and Tube
-
ISO 228-1:2000
AS 1357.1:2019 cites ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation
-
ISO 6957:1988
AS 1357.1:2019 cites ISO 6957:1988 Copper alloys - Ammonia test for stress corrosion resistance