AS 2129-2000 (R2016) Flanges for pipes valves and fittings

Abbreviation
AS 2129-2000
Valid from
17/01/2000

Information provider
Intertek Inform
Author
Standards Australia
Information type
Australian Standard
Format
PDF, HARD COPY


Description

This Standard specifies requirements for circular flanges of nominal sizes DN 15 to DN 3000, inclusive, and their bolting for use on pipes, valves, fittings and other pressure-retaining equipment containing fluid at pressures up to 19 300 kPa and at temperatures in the range -200C to +525C. These flanges are manufactured from carbon steel, carbon-manganese steel, alloy steel, stainless steel, grey iron, malleable iron, ductile cast iron*, or copper alloy.

This Standard is applicable to flanges for water, steam, compressed air, chemical and petroleum plants, hydraulic piping and where other Standards require compliance with this Standard.

This Standard is not intended to apply to flanges for water or waste water covered by AS 4087. Flanges R, S and T are designated obsolescent and are not recommended for use in new equipment. They are retained to provide for the servicing of existing equipment that is expected to have a long working life. For new equipment, flanges R, S and T should be replaced with flanges to AS/NZS 4331, Parts 1 to 3, ANSI B16.5 or BS 4504 (series). The history of AS 2129 flanges (and its predecessor BS 10) and the future use of these flanges is given in the Preface.

For assistance with locating previous versions, please contact the information provider.
Notes/comments

Standard reconfirmed on 2016/05/27

View on Information Provider website
For assistance with locating previous versions, please contact the information provider.

Standard reconfirmed on 2016/05/27

This resource is cited by:

AS 2129-2000 (R2016) Flanges for pipes valves and fittings

This document is CITED BY:

AS 2129-2000 (R2016) Flanges for pipes valves and fittings

Description

This Standard specifies requirements for circular flanges of nominal sizes DN 15 to DN 3000, inclusive, and their bolting for use on pipes, valves, fittings and other pressure-retaining equipment containing fluid at pressures up to 19 300 kPa and at temperatures in the range -200C to +525C. These flanges are manufactured from carbon steel, carbon-manganese steel, alloy steel, stainless steel, grey iron, malleable iron, ductile cast iron*, or copper alloy.

This Standard is applicable to flanges for water, steam, compressed air, chemical and petroleum plants, hydraulic piping and where other Standards require compliance with this Standard.

This Standard is not intended to apply to flanges for water or waste water covered by AS 4087. Flanges R, S and T are designated obsolescent and are not recommended for use in new equipment. They are retained to provide for the servicing of existing equipment that is expected to have a long working life. For new equipment, flanges R, S and T should be replaced with flanges to AS/NZS 4331, Parts 1 to 3, ANSI B16.5 or BS 4504 (series). The history of AS 2129 flanges (and its predecessor BS 10) and the future use of these flanges is given in the Preface.

View on Information Provider website
AS 2129-2000 (R2016) Flanges for pipes valves and fittings
Description

This Standard specifies requirements for circular flanges of nominal sizes DN 15 to DN 3000, inclusive, and their bolting for use on pipes, valves, fittings and other pressure-retaining equipment containing fluid at pressures up to 19 300 kPa and at temperatures in the range -200C to +525C. These flanges are manufactured from carbon steel, carbon-manganese steel, alloy steel, stainless steel, grey iron, malleable iron, ductile cast iron*, or copper alloy.

This Standard is applicable to flanges for water, steam, compressed air, chemical and petroleum plants, hydraulic piping and where other Standards require compliance with this Standard.

This Standard is not intended to apply to flanges for water or waste water covered by AS 4087. Flanges R, S and T are designated obsolescent and are not recommended for use in new equipment. They are retained to provide for the servicing of existing equipment that is expected to have a long working life. For new equipment, flanges R, S and T should be replaced with flanges to AS/NZS 4331, Parts 1 to 3, ANSI B16.5 or BS 4504 (series). The history of AS 2129 flanges (and its predecessor BS 10) and the future use of these flanges is given in the Preface.

View on Information Provider website
This resource does not cite any other resources.

AS 2129-2000 (R2016) Flanges for pipes valves and fittings

This resource does not CITE any other resources.
Feedback